manualshive.com logo in svg

Cub Cadet 524 SWE, Руководство оператора

Поделиться
Скачать
Cub Cadet 524 SWE Скачать руководство пользователя страница 24

Back out the stop bolt to increase the clearance between 

6. 

the friction wheel disc and friction wheel. See Fig. 8-7.

Slip the drive belt off the pulley and between friction 

7. 

wheel and friction wheel disc. See Fig. 8-7.
Remove and replace belt in the reverse order.

8. 

Friction Wheel Removal

If the snow thrower fails to drive with the drive control engaged, 

and performing the drive control cable adjustment fails to 

correct the problem, the friction wheel may need to be replaced. 

Follow the instructions below. Examine the friction wheel for 

signs of wear or cracking and replace if necessary:

Allow the engine to run until it is out of fuel. Do not 

1. 

attempt to pour fuel from the engine.

Place the shift lever in third Forward (F3) position.

2. 

Carefully pivot the snow thrower up and forward so that it 

3. 

rests on the auger housing.
Remove the frame cover from the underside of the snow 

4. 

thrower by removing the self-tapping screws which secure 

it. Remove the right-hand wheel by removing the screw 

and bell washer which secure it to the axle. See Fig. 8-8.

Stop Bolt

Figure 8-7

Figure 8-8

24

s

ectiOn

 8 — s

ervice

Содержание 524 SWE

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды