Cub Cadet 29HP Tank 53AB5GFZ750 Скачать руководство пользователя страница 5

5

ture. Keep sparks and flames away at all 
times.

11. When looking for oil leaks, never run your 

hand over hydraulic hoses, lines or fittings. 
Never tighten or adjust hydraulic hoses, lines 
or fittings while the system is under pressure. 
If high-pressure oil penetrates the skin, the oil 
must be removed within a few hours by a doc-
tor familiar with this form of injury or serious 
complications may result.

B. Related to Fuel

1.

Fuel is highly flammable and its vapors can 
explode if ignited. Please respect it.

2.

Do not smoke or  permit others to smoke 
while handling fuel.

3.

Always use approved containers for fuel and 
fill slowly to decrease the chance of static 
electricity buildup and spillage.

4.

Store fuel in well ventilated and unoccupied 
buildings away from sparks and flames.

5.

When dispensing gasoline into approved con-
tainers, place the container on the ground 
when refueling to avoid a possible static elec-
tricity ignition of fuel vapors.

6.

Do not fill containers while it is inside a vehi-
cle, trunk, the bed of a pickup or floor of a 
trailer.

7.

Always shut off the engine and permit it to 
cool before removing the fuel tank cap.

8.

Always fill the fuel tank outdoors.

9.

If the fuel container spout will not fit inside the 
fuel tank opening, use a funnel.

10. When filling the fuel tank, stop when the fuel 

reaches one inch from the top. This space is 
necessary for tank expansion. Do not overfill.

11. Wipe up any spilled fuel.

C. When Mowing

1.

Keep adults, children and pets away from the 
area to be mowed.

2.

When operating this mower in the forward 
direction, DO NOT allow the steering levers to 
return to the neutral position on their own. 
Always maintain a firm grip on the levers, 
operate them smoothly and avoid any sudden 

movements of the levers when starting or 
stopping.

3.

If the mower is equipped for side discharge, 
never use the mower without the discharge 
chute installed and placed in the down position.

4.

Always remove debris and other objects from 
the area to be mowed.(Note: debris and loose 
grass will reduce traction.)

5.

Mow only in daylight.

6.

Watch for holes, sprinkler heads and other 
hidden hazards.

7.

Avoid driving too close to trees, creeks, 
ditches, sand traps and other obstacles.

8.

Before backing up, check behind you and 
watch where you’re going.

9.

Always reduce speed when making a turn, 
and when grass is wet.

10. Always mow across slopes, never up and 

down the slope. Do not operate on steep 
slopes and slow down before turning.

11. Be careful when crossing gravel paths or 

roadways. Always turn off the blade clutch 
switch and wait until the blades stop rotating 
and raise the cutting deck to the transport 
position. Always allow other vehicles to have 
the right-of-way.

12. If you hit a solid object while mowing, turn off 

the blade clutch switch, place the left and right 
steering levers in the neutral, opened-out 
position, move the throttle to slow, set the 
parking brake, shut off the engine and take 
the key from the ignition switch. Inspect for 
damage. Repair any damage. Make sure the 
blades are in good condition and that the 
blade bolts are tight before restarting the 
engine.

13. Never leave the mower unattended without: 

turning off the blade clutch switch; placing the 
left and right steering levers in the neutral 
opened-out position; moving the throttle to 
slow; setting the parking brake; shutting off 
the engine and taking the key from the ignition 
switch.

14. Never walk or stand on the discharge side of a 

mower with the engine running. Turn off the 
blade clutch switch if another person 
approaches while you are operating the 
mower.

15. Never attempt to operate the traction unit 

without the mowing deck attached.

16. Keep the mower and especially the engine 

and hydraulic components clean and free of 
grease, grass and leaves to reduce the 
chance of fire and to permit proper cooling.

Содержание 29HP Tank 53AB5GFZ750





























Отзывы: