10
4.
Electric Blade Clutch Switch: (See Figure
1.) Located on the right side of the mower
beside the ignition switch. This is an “on/off”
push pull switch that controls the electric
blade clutch which supplies power to the cut-
ting blades through the PTO. The switch must
be turned off to start the engine and should
be turned off for safety any time another per-
son approaches the mower or the mowing
deck is raised to the transport position. Power
to the electric clutch will also be cut off if the
operator leaves the operator’s seat.
5.
Parking Brake: (See Figure 3.) Located on
the left side of the traction unit. The handle is
an overcenter lever which applies the drum-
type brake on each drive wheel when the han-
dle is pulled to the rear. The brake must be
engaged in order to start the engine.
6. Deck Lift Handle and Foot Pedal Lift
Assist: (See Figure 3.) Located on the right
front corner of the mowing deck. Raise the
mowing deck to the transport position, by pull-
ing the lever to the rear and moving it inward
into the stop for transport. To lower the mow-
ing deck, pull the deck lift handle and move it
outward. This lower’s the deck to the cutting
position.The foot pedal lift assist (not pictured
above) can provide “lift assist” to the hand
lever or with “foot effort only”. To provide
assistance to the lift handle: remove the
detent pin from the pedal assembly. Fold the
pedal down to the horizontal position so the
hole in the pedal aligns with the hole in the
lever. Re-install the detent pin. Pull on the Lift
handle and depress the foot pedal to raise the
deck. Lifting with “foot effort only” depress the
foot pedal (the hand lever will lock into trans-
port position if fully depressed). To release the
lift mechanism depress the foot pedal, move
the hand lever outward and slowly reduce foot
pedal effort to lower the mechanism. To ser-
vice the unit: Remove the detent pin from the
pedal assembly. Fold the pedal up to vertical
position so the hole in the pedal aligns with
the hole in the lever. Reinstall the detent pin.
This is the required position for the foot pedal
for the foot platform to tilt forward and to
access some of the machines components.
7.
Fuel Shutoff Valve: (See Figure 4.) Located
behind the operator’s seat, the valve has three
(3) positions: “off”, “Left Tank”, “Right Tank”.
Close this valve if you are not going to run the
mower for a period of 30 minutes or more to
prevent flooding the engine. The fuel system
operates at 25 psi when the ignition switch is
in the “on” position.
Note:
In the left tank position, fuel will be
drawn from the left tank only, and excess fuel
not consumed by the engine will be returned
to the left tank. This also applies to the right
tank.
8.
Seat Adjustment Lever: The Seat Adjust-
ment Lever is located beneath the seat. The
Seat Adjustment Lever is used to move the
seat forward and backward. To place the seat
in the desired position pull the seat adjust-
ment lever to the left then push the seat for-
ward or back to the desired position. Release
the lever so the seat will lock in place.
9.
Digital Tachometer and Hourmeter: (See
Figure 1) Located on the right side of the
mower in front of the ignition switch. When the
machine is running the tachometer displays
engine rpm. When the machine is off the
tachometer displays running time.
10. Warning Lights: Indicator lights are provided
to notify when conditions of “Low oil pres-
sure”, “High temperature coolant”, “Low alter-
nator output”, and “Trouble” are present.
Note:
There will be a flashing “LUBE” for
each recommended lubrication interval. There
is a flashing “OIL” at each recommended
engine oil and filter change.
Park-
Brake
Steering Levers
Deck Lift Handle
Figure. 3
Figure. 4
Содержание 29HP Tank 53AB5GFZ750
Страница 27: ...27 WIRING DIAGRAM GD 02000587...
