background image

6

Tighten the two wing nuts already in place on the 
upper holes and secure the handles firmly. Refer to 
Figure 2.

Slide the shift rod connector down over the end of 
the lower shift rod as shown in Figure 2. Tap the 
connector until it 

locks

 on the lower shift rod.

NOTE: 

If the connector is not properly assembled, the

shift rod will pivot and you will not be able to change
direction or speed of the snow thrower.

Remove the hairpin clip from the upper chute crank 
and slide the upper chute crank through the upper 
chute crank bracket and into the lower chute crank. 
Align the two holes on both chute cranks and insert 
the hairpin clip removed earlier, through these 
holes. Refer to Figure 4.

Figure 4

If not already attached, slip the cables that run from 
the handle panel to the discharge chute into the 
cable guide located on top of the engine as shown 
in Figure 5.

Figure 5

Unwrap the headlight wire which is attached to the 
headlight, beneath the handle panel. Wind the 
headlight wire around the lower right handle until 
excess slack is removed. Refer to Figure 6.

Plug the wire from the headlight into the alternator 
lead coming from the right side of the engine, 
underneath the fuel tank as shown in Figure 6 inset.

Figure 6

Final Adjustments

NOTE: 

It is helpful to read Section 3, Knowing Your

Snow Thrower, to help identify certain areas of the
snow thrower before performing adjustments.

Traction Control and Shift Lever 

To check the adjustment of the traction control and shift 
lever, proceed as follows:

Move the shift lever into sixth (6) position. 

With the traction control released, push the snow 
thrower forward, then pull it back. The machine 
should move freely. 

Engage the traction control and attempt to move 
the machine both forward and back, resistance 
should be felt.

Move the shift lever into the fast reverse (R2) 
position and repeat the previous two steps. 

If you experienced resistance rolling the unit, either 
when repositioning the shift lever from 6 to R2 or when 
attempting to move the machine with the traction 
control released, adjust the traction control 
immediately. To adjust, proceed as follows:

Loosen the jam nut on the traction control cable 
and UNTHREAD the cable one full turn. 

Recheck adjustment.

Retighten the jam nut to secure the cable when 
correct adjustment is reached.

NOTE: 

For more details, refer to Traction Control

Adjustment on page 11.

Auger Control 

Check the adjustment of the auger control as follows:

Push down on the auger control until the small 
rubber bumper contacts the upper handle. There 
should be a small amount of slack in the auger 
control cable. 

Release the auger control. The cable should be 
straight. Make certain you can depress the auger 
control against the left handle completely.

Upper Chute Crank

Lower Chute Crank

 

Hairpin Clip 

Upper Chute

Crank Bracket

Cable Guide

Discharge Chute

Alternator Lead

Lamp Wire

Alternator
Lead

(Wheels left out for clarity)

Содержание 1345 SWE





























Отзывы: