background image

DOC00101-01

4-7

CTPhone 1900 System Configuration

Table 4-A.  System Settings

Parameter

Description

Units/

Range

Recom-

mended 

Setting

Your

Setting

System ID

ID for this CTPhone 1900 system. 
Handsets must be programmed with 
this ID to operate in this system. The ID 
for your system is written on a label on 
the CTPhone Controller.

n.a.

ID shown 
on Control-
ler label

Base Station 1 ID

ID of the first base station connected to 
this CTPhone Controller.

0–31

Base Station 2 ID

ID of the second base station con-
nected to this CTPhone Controller.

0–31

Stop Ringing Time

Length of time the CTPhone Controller 
waits after last detection of ring voltage 
on a line before concluding ringing has 
stopped.

100 ms

1

1

For example, a setting of 2 means 2 x 100 ms or 200 ms.

45

Dial Tone Delay

Length of delay between a user press-
ing CALL key and receiving dial tone. 
The delay may be necessary to elimi-
nate the possibility of a user dialing 
before the office telephone system is 
ready.

100 ms

1

2

DTMF Cycle Duration Duration of the full DTMF cycle (length 

of tone plus length of silence between 
tones) used to perform dialing and other 
telephone system operations.

10 ms

2

20

DTMF Off Duration

Duration of silence between DTMF 
tones.

10 ms

2

2

For example, a setting of 2 means 2 x 10 ms or 20 ms.

10

Hook Flash Duration

Duration of the hookflash used to signal 
the office telephone system.

100 ms

1

5

FT Pause Duration

Duration of pause events in Feature 
Table.

100 ms

1

10

FT Inter-Event Pause Duration of pause between events in 

Feature Table.

100 ms

1

1

Second BS Service
Enabled

TRUE if this CTPhone Controller pro-
vides service for a second base station; 
FALSE if it doesn’t or the second base 
station is out of order.

n.a.

Содержание CTPhone 1900





































































































































Отзывы: