background image

7

Installation - Sensor

2. Fitting the sensor

NB:

 If testing the sensor prior to mounting, the sensor must be placed in the fixing bracket 

so as not to activate the anti-tamper function. mKomfy 1.8 sensor f.o.m. snr: 2024-000001 
has a new fixing bracket (with lug) which is not compatible with the previous version.

1.  Remove the battery cover and fit batteries (3 x AA). 

2 beeps = battery OK. 

2.  Tear off the red protective film on the bracket.

Mount the sensor on a flat, clean surface on the wall above the 
centre of the cooker at a height of 45-55 cm, see figure 2. For other 
installation heights, see page 9.

NB: If the material on the wall surface is unsuitable for mounting with 

tape, a screw must be used in the centre of the bracket foot.

3.  Press the control button on the sensor once. A short beep confirms 

that the sensor is in communication with the socket and working. 
If there is no beep, check that the sensor has been correctly mounted 
in the fixing bracket (anti-tamper function).

4.  Make sure that only the green LED on the socket lights up when the 

cooker is connected and turned off. If the yellow LED lights up, the 
cooker’s standby electricity consumption is higher than the standard 
setting. In this case the level in the mKomfy can be calibrated to the 
cooker’s actual electricity consumption, see pages 10 and 11.

*

*

45 til 70 cm

30 cm

60 cm

60 cm

30 cm

Senter komfyrvakt

Senter komfyr

figure 2

sensor height 45-75 cm for hobs <= 60 cm wide
sensor height 65-70 cm for hobs <= 90 cm wide

Centre of Cooker Guard

Centre of cooker

6

Installation – Socket

1. Fitting the socket (may 
only be carried out by 
authorised personnel)

1.  Connect and fit the 

socket.

2.  Connect the cooker 

plug to the Cooker 
Guard’s socket.

3.  Check that power 

is connected to the 
socket.

DO  NOT CONNECT!

If there is no radio communication from the sensor, the plug will shut off after 5 minutes. 

The sensor and socket are paired at the factory and ready to install.

If re-pairing is necessary:

Remove at least once battery from the sensor (you can get batteries ready for 
the sensor, but DO NOT fit them).

1. 

Give the Socket control button a quick press. Yellow LED flashes.

2.  Hold the control button on the sensor in and fit batteries in the sensor.
3.  There are 4 beeps, the blue LED on the socket flashes and the socket 

turns off.

4.  Release the control button on the sensor.

The sensor and socket are now paired.

Status LEDs

Green

lights up   

when socket is ON

Blue   

flashes 

when data is received from paired units (e.g. sensor)

Blue + 
Green

flash  
alternately

1 minute after emergency mode* is activated, and continues 
to flash while the product is in emergency mode (12 hours).

Red   

flashes 

if socket overheats – socket is turned OFF

Red    


beeping

if there is an error, e.g. external switch paired before 
sensor

Yellow  lights up   

when cooker’s electricity consumption exceeds 1.2 A

**

Yellow    flashes  

in pairing mode

emergency mode = all safety functions deactivated. See page 5.

** 

1.2 A is the factory default. After calibration, the LED lights up when the new setting is 

exceeded (page 11)

Control button

Содержание 6251650













Отзывы: