background image

18

A short circuit is indicative of a lack of electrical resistance, removing the ability 

to measure the impact from a change in voltage . This instance is largely driven 

by an incorrect wiring setup . Verify that all wiring connections are attached in 

the correct polarity, and that no signal and common wires are touching . Lastly, 

ensure that the system is free of water and other contaminants .

State 3

 - Input Open Detected

• 

LED is solid red

An open circuit implies a physical disconnect somewhere on the electrical path 

of the circuit . When receiving this error, verify that there is no physical separation 

within the system, such as unattached or broken cabling . Be sure that the 

connector is firmly secured to the accelerometer, and that the accelerometer is 

in good working order .

State 4

 - Device Warning Detected

• 

LED is flashing green in one-second intervals

A detected warning can be due to several things, such as incorrect output wiring 

(e .g ., an open circuit detected on a current output or a short circuit detected 

on a voltage output) or corrupted configuration memory . The device will still 

be processing input data . However, it may be running in a reduced state or 

return unexpected results (e .g ., if memory is corrupted, the unit will default to 

the standard ISO configuration until reprogrammed) . If this state is detected, 

carefully inspect all wiring for secure connections and cycle power to the device . 

If the warning persists, the configurator can be used to determine the root cause 

and corrective action .

State 5

 - Fatal Error

• 

LED is flashing red in one-second intervals

In the case of a fatal error, the device has detected some non-recoverable 

hardware issue which could have been caused due to physical damage or misuse . 

Processing will be disabled in this case . Communication with the configurator 

may or may not work depending on the root cause but should be attempted as 

it may state the error that occurred . In some cases, cycling power to the device 

can remedy the issue .

State 6

 -  Programming and Startup

• 

LED is solid orange

Содержание SCE400 Series





















Отзывы: