background image

Form I-RA/D 350/500, P/N 131090R12, Page 5

Conventions Used in this Manual
Hazard Intensity Levels

DANGER:  Failure  to  comply  will  result  in  severe 

personal injury or death, and/or property damage.
WARNING:  Failure  to  comply  can  result  in  severe 

personal injury or death and/or property damage.
CAUTION:  Failure  to  comply  could  result  in  minor 

personal injury and or personal damage.

NOTE: 

Additional Warnings are also included throughout this manual.

CAUTION:  These  heaters  are  designed  to  provide 

economic  disposal  of  used  oils.  Used  oil  is  an 

inconsistent fuel and may contain water and/or foreign 

materials which may cause the unit to shut down. A 

secondary source of heat should always be provided 

to the building; do not depend on this heater as your 

only source of heat. This will prevent building damage 

should the heater become inoperable during sub-

freezing weather. 

WARNING: Approved  fuels  are  No.  2  fuel  oil  and 

used  automotive  transmission  fluid  and  crankcase 

oils  up  to  50  weight.  Do  not  attempt  to  burn  any 

grade  of  gasoline,  paint  thinner,  or  non-approved 

fluids. Adequate ventilation must be provided in any 

enclosure where storage tanks, pumps, or accessories 

are installed. 

This heater is not designed for use in hazardous atmospheres contain-

ing flammable vapors or combustible dust, or atmospheres containing 

chlorinated or halogenated hydrocarbons.

WARNING:  Failure  to  provide  proper  venting  could 

result in death, serious injury, and/or property damage. 

Units must be installed with a flue connection, draft 

regulator and proper vent to the outside of the building. 

Safe operation of any gravity vented heating equipment 

requires  a  properly  operating  vent  system,  correct 

provision for combustion air, and regular maintenance 

and inspection.

Safety 

Warnings

Secondary Heat 

Source

!

Venting

Fuels

Hazardous 

 

Atmosphere

Содержание RA 350





























































Отзывы: