Striker face
plate
11
11
. Position the striker face plate in the
centre of the striker body - this may need to
be adjusted in the steps following. Insert the
striker face plate screws and loosely tighten.
12
. Close the door. When the striker is fitted
correctly the magnet will draw the plunger
forward. If this does not happen the striker is
misaligned with the plunger (see below). If the
alignment is correct, tighten the screws and
skip to Step 14; otherwise continue to Step 13.
✗
✗
✓
12
13
Striker
face plate
screws
2.5mm
(3/32”)
2.5mm
(3/32”)
Striker
Plunger
13
. The striker allows 2.5mm (3/32”) of
adjustment in each direction when the
striker face plate is fitted in the centre of
the striker body.
To adjust the face plate position, loosen
the striker face plate screws slightly and
adjust the face plate up or down to allow
14
. Manually push the plunger forward until
there is no gap between spring reservoir one
(SR1) and spring reservoir two (SR2).
Restrain the plunger nut using the large end
of one of the two identical supplied spanners.
Push
here
➟
SR1 SR2
No gap
14
Turn
clockwise
15
15
. Place the small end of the second spanner
across the flats under the head of the plunger.
Keep the spanner restraining the plunger nut
stationary while turning the second spanner
clockwise.
Continue to turn the spanner until there is no
longer a gap between the spanner and the
shroud face.
Now turn the spanner anti clockwise half a turn.
The plunger should now be adjusted correctly.
Slide the door closed to check that it latches.
If the snib button is hard to push down or the
plunger doesn’t engage with the striker, adjust
as necessary.
Front View Rear View
16
. If installing a snib/snib or a snib one
side privacy handle proceed to Step 17,
otherwise, fit the emergency release button
(with the spring attached) into the two holes
in the arm of the locking slider.
17
16
Emergency
release
button
Locking
slider arm
Front
flange
17
. Fit the remaining side handle to the
chassis (using the 3x side handle to chassis
screws) by sliding the front flange of the
handle under the heads of the three screws.
Tighten the screws.
Spring
(attached)
18
. Fit the privacy face plate to the
chassis using the 3x handle face plate
screws.
Handle face
plate screws
Privacy
face
plate
8
. Remove the striker from its box. Remove
the striker face plate from the striker body.
Insert the 2x striker nuts into the recess in the
back of the striker body.
Insert the 2x striker face plate screws through
the slot in the front face of the striker body
and into the striker nuts. Loosely tighten the
screws.
Striker nuts
Striker
nuts
Rear View
Striker body
7
. Open the door. Transfer the horizontal line
across the centre of the closing jamb. This
line represents the top of the striker cut out.
A double-sided striker cut out template has
been provided:
- Use template labelled ‘FLUSH striker
template’ if you are installing a snib/
emergency or snib/snib privacy handle.
- Use template labelled ‘RECESSED striker
template’ if you are installing a snib one side
privacy handle.
32 40
32 40
40 32
40 32
2
3
7
CL
5
4
6
Horizontal
line
Centre of
closing jamb/
centre of
door closing
position
CL
7
Striker
body
Striker face
plate screws
Striker
mounting
wood screws
10
Striker face
plate screws
9
. Insert the striker body, with the striker
face plate screws and the striker nuts
attached, into the cut out in the closing
jamb.
Striker
face
plate
screws
9
10
. Remove the striker face plate screws.
The striker nuts are now trapped in position.
18
5
7
6
8
PAGE
PAGE
PAGE
PAGE
Fitting Emergency Release
Adjusting the Plunger
Fitting the Remaining Side Handle
Fitting the Face Plate
Gap
No
gap
Striker face
plate screws
8
Screw the 4x striker mounting wood screws
into the closing jamb.
© Cavity Sliders Limited. CAVILOCK
®
CL400
®
MAGNETIC (O.D. 2013) PRIVACY INSTRUCTIONS.
60905/CL400ZA925 - 05.2017
All copyright and other property in this document is reserved by Cavity Sliders Limited. Details and specifications are subject to
change without notice. Whilst all care is taken to ensure the accuracy of all information, no responsibility will be accepted for any
errors or omissions. ® CS FOR DOORS, CS CAVITY SLIDERS and CAVILOCK are Registered Trademarks. Patents pending.
Fitting the Striker
Fitting the Striker
Adjusting the Plunger
Spanner
Plunger
nut
the plunger to penetrate the striker face plate.
If the plunger still fails to penetrate the striker
face plate, the door height may need to be
adjusted.
Plunger
flats
Shroud
face
Red
section
Note: the locking slider arm may have been
pre-cut depending on the width of the door.
The drawing below demonstrates a cut
slider arm.
If you are installing a handle that has
LOCKED/UNLOCKED indication, ensure
that the green and red Emergency Release
Indicator Label has been applied with the
RED section at the TOP.
Emergency release
indicator label
Two
holes
Cavity Sliders Limited
Auckland Head Office
5 - 7 Rakino Way
Mt Wellington
Auckland, NZ
T +64 9 276 0800
F +64 9 276 2525
[email protected]
Recyclable
Packaging
www.csfordoors.co.nz
www.cavitysliders.com.au
www.cavitysliders.com
