background image

OPERATOR’S MANUAL

3

To get the maximum benefi t from your saw 
and ensure maximum safety, be sure to 
read and understand this manual 
thoroughly and follow the safety 
instructions provided
Always use:
• 

Protective helmet

• 

Ear protection

• 

Protective glasses or full face 
protection  

Wear hand protection

� 

WARNING

• Do NOT operate saw without side cover.

• Do NOT operate saw without baffle drain.

• Do NOT use this saw cover on any other saw model.

• Failure to observe these precautions can result in serious injury.

SYMBOLS & LABELS

� 

WARNING

•  Do not exceed 90psi (6 bar) air

   pressure or 124 cfm (3.5m

3

/min) air

   volume

•  Do NOT insert tool into slot narrower

   than chain.

•  Do NOT operate tool without solid 

   footing and firm hand grip.

SAFETY RULES

To get the maximum benefi t from your saw, and ensure maximum safety, be 
sure to read this manual thoroughly and follow the safety instructions provided.  

EXPLANATION OF WARNING LEVELS

IMPORTANT

Indicates a hazard with a medium level of risk which, if not avoided, could result 
in death or serious injury.

Indicates a hazard with a low level of risk which, if not avoided, could result in 
minor or moderate injury.

Indicates a potential situation exists which, if not avoided, may result in damage 
to your saw or property.

Indicates a hazard with a high level of risk which, if not avoided, will result in 
death or serious injury.

    

WARNING

    

CAUTION

   

DANGER

Содержание CS536664

























Отзывы: