Crunch GTX 2200 Скачать руководство пользователя страница 27

25

G T X 4 4 0 0

2 7

EXAMPLE 3-Channel Mode: 1 x Stereo System & 1 x Mono Subwoofer bridged

INTERCONNECTION

• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables. If a

separate SUB OUT from your headunit is available, use this for the LINE INPUT CH1/2 on the amplifier.

As alternative you can connect the loudspeaker outputs of your headunit with the HIGH LEVEL INPUT. Never use the High Level Inputs
and the RCA inputs at the same time. This may damage the amplifier seriously. Attend therefor the descriptions on page 28.

• Connect the speakers with SPEAKER CH 3 - and + CH 4 - and the subwoofer with the SPEAKER OUTPUT CH1/2

+ BRIDGED - of the amplifier.

• Ensure by any means, that the total impedance load of all speakers per channelpair (CH3 & CH4) is not lower than 2 ohms and the total

impedance load of the subwoofer (CH1 & CH2) is not lower than 4 ohms. Too low impedance cause high temperature and will shut down

the amplifier operation.

INPUT MODE-Switch

• Select the 4CH position on the INPUT MODE switch. If there is only one RCA stereo audio cable from the headunit available, connect 

the CH1/2 RCA line inputs and select the 2CH position.

CROSSOVER SETTINGS CH1/2 (SUBWOOFER )

• Attend the regarding notes on page 28.

LEVER CONTROLLER CH1/2 (SUBWOOFER )

• Attend the regarding notes on page 28.

BASS BOOST CONTROLLER CH1/2 (SUBWOOFER )

• Attend the regarding notes on page 28.

CROSSOVER SETTINGS CH3/4 (STEREO SYSTEM)

• Attend the regarding notes on page 25.

LEVER INPUT CONTROLLER CH3/4 (STEREO SYSTEM)

• Attend the regarding notes on page 25.

BASS BOOST CONTROLLER CH3/4 (STEREO SYSTEM)

•  The BASS BOOST controller must be turned to 0 dB position in this interconnecting example .

FR

FL or SUB OUT

Connect the stereo RCA output (FL/FR or SUB OUT and RL/RR) of the

headunit with LINE INPUTS CH1/2 and CH3/4 of the amplifier

RL

RR

Speaker

left

2 – 8 Ohms

Speaker
right
2 – 8 Ohms

Switch position CH1/2 = LP and CH3/4 = HP or FULL

INPUT MODE = 3 CH

Subwoofers

4 – 8 Ohm

Содержание GTX 2200

































Отзывы: