9
(1) STP (Frequency Tuning Step)
This menu is to set tuning step when adjusting frequency by
CLARIFIER knob
Options:
10HZ
、
100HZ
、
1KHZ
、
10KHZ
Default:
10HZ
(2) CLA (CLARIFIER knob functions setting)
This menu is to set functions turned by CLARIFIER knob. Options are
as follows:
FIN:
Fine regulation. When this option is selected, users can fine
tuning the receiving frequency by rotating the CLARIFIER
knob. In tuning process, the transmitting frequency can not be
regulated by the knob and “1” icon will appear on the LCD.
RT:
When this option is selected, users can regulate the frequency of
both transmitting and receiving. In tuning process, “2” icon will
appear on the LCD.
T:
When this option is selected, users can only regulate the
transmitting frequency. In tuning process, “3” icon will appear on
the LCD.
Default:
RT
COA:
When this option is selected, press PUSH and turn CLARIFIER
knob to realize COARSE function.
When pressing this key, "2" icon will appear on far left of the
LCD. Under this condition, rotate the CLARIFIER knob to change
frequency of both transmitting and receiving.
T:
When this option is selected, press PUSH and turn CLARIFIER
knob to change transmitting frequency. When pressing this key,
"3" icon will display on the far left of the LCD. Under this condition,
rotate the CLARIFIER knob to change the transmitting frequency
only.
STP:
When this option is selected, PUSH function will change
Frequency Tuning Step of CLARIFIER knob. Press this key, then
the corresponding frequency bit would blink.
Default:
STP
(4) ASQ (Automatic Squelch Control)
ASQ control setting. It has same function with AQ button on the
microphone.
Default:
OFF
(5)TOT (Transmitting Time-Out-Timer)
This menu is to set transmitting TOT time. When pressing PTT key
at a single time longer than the due time setup in advance, the radio
would stop transmitting automatically and loudspeaker will emit voice
prompt till PTT key is released. Then, the radio can transmit again.
Options:
30-600s
Step:
30s
Default:
180s
(3) PUS (PUSH Function Setting)
This menu is to set functions realized via PUSH knob. Options are as
follows:
10
(6) SC Scanning Type Selection
This menu is to set Scan Type. Options are as follows:
SQ:
When SQ is selected, scan would stop when a valid signal
is detected. The radio would resume scanning after signal
disappears for 5s.
TI:
When TI is selected, scan would stop when a valid signal is
detected. The radio would resume scanning 5 seconds later,
whether signal disappears or not.
Default:
SQ
(7) TSR (Transmitting SWR Protection)
This menu is to choose whether to enable Transmitting SWR
Protection function or not.
ON:
When ON is selected, the radio will detect the SWR of antenna.
Once the SWR is beyond the SWR set in advance, the radio
would prohibit transmitting automatically and loudspeaker will
emit voice prompt. Then, “HI S” icon will display on the LCD to
remind you that the antenna SWR is too high or antenna do not
connect well.
OFF:
When OFF is selected, SWR Protection function is disabled.
NOTE:
To protect the radio from long transmission under high SWR,
the radio would automatically start SWR Protection once the
SWR Value is higher than 20:1.
Default:
ON (SWR=<10:1)
(8) TDC (Power Supplied Voltage Protection)
This menu is to choose whether to enable Power supplied Voltage
Protection function or not.
ON:
When ON is selected, the radio will detect the supplied voltage.
Once the voltage surpasses the voltage setup in advance, the
radio would display “DC LO” or “DC HI” to remind you that the
voltage is not in normal state. Meanwhile, the radio will prohibit
transmitting and emit beep prompt.
OFF:
When OFF is selected, the Power Supplying Voltage is disabled.
Default:
ON (DC 10.5V-16V)
(9) TLD (Content displayed on the LCD when transmitting)
This menu is to set the content displayed on the LCD when
transmitting.
TF:
When TF is selected,LCD would display transmitting
frequency when transmitting.
SR:
When SR is selected, LCD would display SWR value of antenna
when transmitting, for example: "1.2" on the LCD.
BAT:
When BAT is selected, LCD would display Supplied Voltage
when transmitting, for example: "13.8DC" on the LCD.
TOT:
When TOT is selected, LCD would display TOT remaining time
when transmitting. And TOT would count down till remaining time
is 0, for example: "170" displayed on the LCD display.
Default:
TF
(10) RBF (ROGER BEEP Frequency Setting)
Содержание SS 6900
Страница 1: ...10 METER RADIO USER S MANUAL Downloaded from www cbradio nl ...
Страница 2: ......
Страница 21: ......
Страница 22: ......
