background image

 

3

10. Use the correct battery and regulator (if applicable) for your ignition  

11. Use the correct switch for your ignition  

12. Use an appropriate fuel tank, plumbing lines, and installation  
13. Use the appropriate fuel for break in and after break in (gas and oil)  

14. Insure adequate filtering of your fuel 

15. Maintain your engine properly, keeping it clean, etc. 

16. Use a pre-flight check list before flying your model 

17. Secure your model properly when starting 
18. Not use your fingers or hand to start your model 

19. Adjust your carburetor correctly 

20. Not adjust your carburetor while the engine is running 

21. Insure that your spark plug is in good condition and is secured 

correctly 

22. Insure that your ignition wires are not frayed and are protected 

23. Insure that your ignition cap is securely mounted 

24. Keep all people behind the line of the prop 

25. Do not put anything (i.e., fingers, body parts, objects, et al) into the 

rotating propeller  

26. Keep children away. All spectators should be kept a safe distance away 

from the running engine. 

27. Wear proper apparel. Do not wear loose clothing, gloves, neckties, 

jewelry, or neck straps for your radio which may get      caught in the 

moving propeller.  

28. Always wear eye protection when starting the engine. 

29. Do not operate this engine if you are under the influence of any drugs, 

alcohol or medication that could affect your   ability to use the 

engine properly.  

 

Содержание GF45I









Отзывы: