background image

Operation Manual

CTs Multi-Channel Power Amplifiers

page 26

page 27

CTs Multi-Channel Power Amplifiers

Operation Manual

Problem: 

Green Preset indicator is flashing, or is not flashing.

Possible cause: 

This is not a problem. This indicator signals the 

number of the current preset, if active, by flashing a series of flashes 
equal to the current preset number. A preset is considered “active” if 
the USP/CN settings match those in the selected preset. If a change is 
made to any setting then the preset is considered “inactive,” and the 
indicator stops flashing.

Problem: 

Both right indicators flash yellow in unison to report a fatal 

error.

Possible cause:

 

An unexpected condition within the CobraNet 

inter face has been detected. 

NOTE: Actual product artwork may vary slightly.

5 Troubleshooting

 (continued)

Problem: 

Data indicator is not flashing, even though a valid 

com mand was sent.

Possible causes: 

• Command was not addressed to the USP/CN.
• Network cable is disconnected or broken.

To assist with troubleshooting, System Architect can set an option for 
force the data indicator on.

Problem: 

Green LINK/ACTIVITY indicator in network connector does 

not illuminate or flash.

Possible cause:

 Ethernet link is broken, or network connection is 10 

Mbps. Check Ethernet connections to the network switch.

Problem:

 

Computer does not communicate with the network 

devices.   

Possible cause:

 Incorrect wiring. See Section 2.10 on network 

wiring.

   

Performance

CTs 4200USP/CN

CTs 8200USP/CN

Frequency Response (at 1 watt, 20 Hz - 20 kHz)

± 0.5 dB

± 0.5 dB

Phase Response (at 1 watt, 10 Hz - 20 kHz)

± 35°

± 35°

Signal to Noise Ratio below rated power (20 Hz to 20 kHz)

100 dB unweighted

100 dB unweighted

Total Harmonic Distortion (THD) at 1 watt, from 20 Hz to 20 kHz

< 0.05%

< 0.05%

Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, 

from 163 milliwatts to full bandwidth power, typical

< 0.05%

< 0.05%

Damping Factor: 10 Hz to 400 Hz

>180

>180

Crosstalk (below rated power, 20 Hz to 1 kHz)

> 80 dB

> 80 dB

Common Mode Rejection (CMR) (20 Hz to 1 kHz)

> 50 dB

> 50 dB

DC Output Offset (Shorted input)

< ± 5 mV

< ± 5 mV

Input Impedance (nominal) (balanced, unbalanced)

20 kilohms, 10 kilohms

20 kilohms, 10 kilohms

Maximum Input Level (before input compression)

+ 20 dBu

+ 20 dBu

Load Impedance (Note: Safe with all types of loads)  

      Stereo 

      Bridge Mono

 

4/8 and 25 ohms (70V)  

8/16 and 50 ohms (100V) 

 

4/8 and 25 ohms (70V)  

8/16 and 50 ohms(100V) 

Voltage Gain (at maximum level setting), 1.4V sensitivity 

     4/8 Ohm Operation 

     70V Operation 

     100V Operation

 

20:1 (26 dB) 

50:1 (34 dB) 

71.4:1 (37 dB)

 

20:1 (26 dB) 

50:1 (34 dB) 

71.4:1 (37 dB)

Required AC Mains (model dependent)

120V, 60 Hz. 220/230/240V, 50 Hz

100V, 50/60  Hz. 120V, 60 Hz. 220/230/240V, 50 Hz

Power Draw at Idle (120VAC mains, all channels in 4/8 ohm mode)

70W

70W

Power Draw at Idle (120VAC mains, all channels in 70V mode)

114W

114W

Cooling

Continuously variable speed forced air, front-to-back airflow

Continuously variable speed forced air, front-to-back airflow

Dimensions: Width, Height, Depth

19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 16.25 in. (41.3 cm) D

19 in. (48.3 cm) W x 5.25 in. (13.3 cm) H x 16.25 in. (41.3 cm) D

Net Weight, Shipping Weight

26 lb. 6 oz. (12 kg), 30 lb. 14 oz. (14 kg) 

36 lb. 6 oz. (16.5 kg), 47 lb. (21.3 kg)                                                 

The following specifications apply to all models in Dual 8/4 ohm mode with 8-ohm loads unless otherwise specified.

6 Specifications

USP/CN (CobraNet Module) 

Specifications

Memory Backup:

 4 Megabit non-volatile FLASH memories for 

backup of run-time parameters, presets, and program storage. 
Capa ble of 10,000 write cycles. 

Communications: 

100 Mb Fast Ethernet conforming to IEEE 802.3.

Overall Audio Performance:
DSP Processing

: Two processors, 32 bit, floating point, 724 µs 

latency.

DAC Conversion: 

24 bit, 250 µs latency.

Dynamic Range: 

103 dB typical (A-weighted, 20Hz–20kHz, audio 

sourced from muted CobraNet channel).

Distortion: 

< 0.1% THD+N, 20Hz–20kHz.

Frequency Response:

 ± 0.5 dB, 20Hz–20kHz.

Input/Output Monitor Accuracy: 

Typically ±1dB.

Maximum Input Level:

 + 20 dBu. 

ADC Conversion:

 24 bit, 250 µs latency.

Содержание CTs 4200USP/CN
























Отзывы: