Crown CT60001HX, Оригинальное руководство пользователя

Страница: 22 / 144

22
English
Lift the foldable clip up and rotate it to the desired
position (see fig. 7).
Recommendations on the power tool op-
eration
Range of application of the power tool
Using the power tool allows different types of work to
be performed� Some of them are listed below�
• Contracting heat shrink pipes, soldering connec-
tors and clamps of sealing and electrical components�
• Changing the shape of acryl, PVC, polystyrene
products, pipes, plates, profiles and wet timber.
•
Repairing surfboards, skis and other sports equip-
ment, repairing bumpers and other plastic automobile
parts�
• Waxing skis, furniture, and antiseptic timber treat-
ment�
• Loosening rusted or tight metal screws, nuts, bolts,
shrink-fitting, heat shrink treatment.
• Welding thermoplastic polymers, PVC and linoleum
flooring materials, PVC coated fabrics, tarpaulin and foil.
• Soldering, tinplating and loosening of soldered
joints�
• Removing lacquer and paint coatings�
•
Drying lacquer and paint coatings, adhesive and
spackling compounds�
• Acceleration of adhesion processes, activation of
adhesives�
• Thawing ladders, stairs, door locks, boot covers, car
doors, water pipes as well as defrosting fridges and
freezers�
• Mold and fungus control, disinfection of animal
housing�
• Lighting charcoal�
Using special nozzles
• Flat nozzle 14 is designed for treating large-area
surfaces�
• Reflector nozzle 15 is used for changing the air flow
direction�
• Point nozzle 16 is for treating small-area surfaces as
well as for soldering�
General recommendations
• If necessary, put an appropriate special nozzle on
gun nozzle
3
�
• Prepare accessories required for work performance
(scraper, palette knife, brush, etc�)�
• Switch on the power tool, as described above�
• After the operation completion switch off the power
tool�
Special recommendations for performing different
types of work (see fig. 8-10)
Paint and coatings removal (see fig. 8)
- install
flat nozzle 14 , heat the surface area until the coat-
ing softens, and remove it with a palette knife�
Thawing water pipes (see fig. 9) - install reflector
nozzle 15 � While moving the power tool, heat a frozen
area from the edge to the middle� While heating plastic
pipes, be careful not to overheat them�
Soldering (see fig. 10) - install point nozzle 16 � Apply
solder paste on the soldering area� Depending on the
material, heat the soldering area for 50-120 seconds,
and then apply solder alloy� The solder alloy must melt
under the workpiece temperature�
Power tool maintenance / preventive
measures
Before carrying out any works on the power tool
remove the battery 7.
Battery maintenance instruction
• Charge timely before the battery 7 is completely
exhausted� Stop operation in low power and charge
it immediately�
• Do not overcharge when the battery
7
is full, other-
wise it will shorten the life time�
• Charge battery 7 in the room temperature of 10°C
to 40°C (50°F to 104°F)�
• Charge battery 7 every 6 months without operation
for a long time�
• Replace worn out batteries in time� Decline of pro-
duction or a significantly shorter runtime of the power
tool after charging indicates aging of the battery 7 and
the need for replacement� It should be taken into ac-
count that the battery
7
may discharge faster if the
works take place in the temperature below 0°С.
• In case of long time storage without use, it is recom-
mended to store the battery 7 at room temperature, it
should be charged to 50%�
Taking care of accessories
Keep special nozzles clean - remove all materials
stuck to them�
Cleaning of the power tool
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean� Regularly
flush the power tool with compressed air thought the
ventilation slots 12 �
After-sales service and application service
Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts� Information about service centers,
parts diagrams and information about spare parts can
also be found under: www.crown-tools.com �
Transportation of the power tools
•
Categorically not to drop any mechanical impact on
the packaging during transport�
• When unloading / loading is not allowed to use any
kind of technology that works on the principle of clamp-
ing packaging�
Li-Ion batteries
The contained Li-Ion batteries are subject to the Dan-
gerous Goods Legislation requirements� The user can