background image

15

TABLE 13.0: ERROR CODES

Error 

Code Meaning

Possible Cause

2

Pressure Switch failed to open

Jumped air pressure switch

• 

Condensate in air pressure switch or switch tubing

• 

Defective air pressure switch

• 

4

Low Flame Signal

Low gas pressure at gas valve inlet

• 

Partially plugged pilot tubing or pilot orifice

• 

Loose connection in ignition cable or ground wiring

• 

Dirty pilot electrode/ground strap

• 

Pilot electrode porcelain cracked

• 

Damaged pilot hood/ assembly

• 

Defective control

• 

6

Pilot Flame detected when no 

flame should be present

Defective gas valve

• 

High gas pressure

• 

Defective control

• 

18

Internal electronics failure

Possible internal problem with boiler control. Cycle power to the boiler and 

• 

replace control if problem persists.  

23

Flame sensed during 30s pre-

purge (before pilot valve opened)

Defective gas valve

• 

High gas pressure

• 

Defective control

• 

29

Air pressure switch failed to 

close

Vent system blockage

• 

Vent system not constructed in accordance with installation manual (exces-

• 

sive length, undersized pipe, wrong terminal, etc)

Condensate or leakage in air pressure switch tubing

• 

Winds in excess of 40mph

• 

32

Boiler water temperature sensor 

failure

Loose sensor connection at control

• 

Defective Sensor

• 

Defective control

• 

35

Duplicate Zone

Error code reserved for future use 

57

Grounded pilot electrode

Condensate or foreign material is shorting pilot electrode to ground.

• 

Ignition cable insulation is damaged and touching ground. 

• 

Pilot is damaged 

• 

58

AC Power Frequency Error

120VAC power supply frequency is incorrect (Should be 60Hz)

• 

120VAC power supply is dirty (consult electrician and/or Utility)

• 

Boiler water temperature sensor common (center wire) is damaged and 

• 

shorted to ground 

59

Line voltage error 

(Supply voltage too high or low)

Power supply voltage is incorrect (should be 120VAC nominal)

• 

Defective or incorrect 24VAC transformer

• 

Loose 120VAC connection or 24VAC connection between transformer and 

• 

control

60

Thermostat input higher than 

threshold

External voltage is applied to thermostat connections (most common cause is 

• 

external transformer in old thermostat wiring. 

61

Line Voltage Unstable

120VAC power supply is dirty (consult electrician and/or Utility)

• 

Loose 120VAC connection or 24VAC connection between transformer and 

• 

control

Large electrical loads elsewhere on the installation are switching on and off, 

• 

causing incoming voltage to swing excessively at boiler.

63

Maximum recycles exceeded 

See Error Code 4 above (boiler lost proof of pilot 6 times in a row)

• 

64

Internal failure

Improper pilot operation

• 

If problem persists, replace control

• 

 

89

EnviraCom communication lost

Should not be observed on BWF or CWD Series Boilers. 

Содержание BWF Series

























Отзывы: