background image

9

TABLE 10b.4: OPERATING MODE PARAMETERS

Parameter # Description

Meaning

bt

Boiler Temperature

Current boiler water temperature measured by the control’s sensor. 

SP

Boiler water set point

Current target temperature (always the same as the high limit setting unless 

Crown outdoor reset card option  is installed). 

HL

High Limit Set point

Boiler will stop firing if boiler water temperature exceeds this value (Circulator/s 

will continue to operate)

HdF

High Limit Differential

If high limit setting is reached, boiler water temperature will need to drop by this 

amount before boiler will again fire during the same call for heat. 

tt

Heat Request Status

Shown as either ON or OFF. Indicates whether there is a call for heat. 

dh

DHW Request Status

Shown as either ON or OFF. Indicates whether there is a call for domestic 

hot water (DHW). Note that if the dh zone on the S9361A is used as a second 

heating zone (see Table 10b.5), this parameter will be shown as OFF and tt will 

be shown as ON when this zone calls for heat.     

FLA

Flame Current

Flame rectification signal (uA)

run

Run Time Hours

Total amount of time gas valve has been open (burner firing) since control was 

new (hours, starting from 1). 

CyC

Boiler Cycles

Total number of burner cycles on the control

Err

Error Number

Present only if the control has detected a problem. See Table 

13.0

 for a list of 

error codes and suggested corrections. 

TABLE 10b.5: ADJUSTMENT MODE PARAMETERS

Status # Description

Factory 

Setting

Permissible Range 

HL

High Limit Set point

180F

140-220F

dF

High Limit Differential

15F

10-30F

Or

Circulator overrun

0 min

0-10 minutes

PP

Thermal Purge time

2 min

2-20 minutes*

St

Thermal Purge Start Temp

140F

140-180F

Pt

DHW Priority

ON

ON or OFF

dh

Use of Second Zone

dh

dh (dhw) 

or 

tt2 (2nd heating zone).

rst

Reset

N/A

OFF or

Momentary ON

F-C

Temperature Units

F

F or C

bAc

Exit Adj. mode

N/A

N/A

                              * Thermal purge time may be reduced to 0 minutes if Crown outdoor reset card is installed. 

Содержание BWF Series

























Отзывы: