BATHROOM FURNITURE RANGE
SVELTE
600 Two Drawer Basin Unit
& Basin
800 Two Drawer Basin Unit
& Basin
1000 Two Drawer Basin Unit
& Basin
1200 Two Drawer Basin Unit
& Basin
SE0611S
SE0811S
SE1211S
SE6000D
SE8000D
SE1200D
39-45kg with basin
46-51kg with basin
60-66kg with basin
73-79kg with basin
SE1011S
SE1000SD
x2
x8
x2
x8
x2
x8
x2
x8
IMPORTANT - Advice and safety - Please read before installation
Tools & equipment needed:
Drill, 8mm Suitable drill bit, Phillips screwdriver, Spirit level, Ruler/tape measure, Pencil,
Silicone sealant (clear).
Please read these instructions carefully before starting installation
and keep in a safe place for future reference. ENSURE the room is
well heated and ventilated.
Check the contents of the pack carefully before installation. Crosswater
will not be held responsible for any de-fit / re-fit costs where faulty product
has been fitted.
If any fault is found with materials or workmanship, it must be reported im-
mediately to the manufacturer. Remedial action will be taken, based on in-
formation received, on condition that: 1. Full details are supplied to the ma-
nufacturer; 2. The product has not been modified or tampered with; 3. The
manufacturer is informed of any damage/shortages prior to installation. 4.
The product has not been installed, or attempts have been made to install.
We do not accept responsibility for any problems that may occur through
incorrect installation.
Advice & Safety
This product should only be fitted by a qualified plumber to NVQ (National
Vocational
Qualification) or SNVQ (Scottish National Vocational Qualification) Level
3. Should the installation be completed by a non-qualified person then the
guarantee may be considered invalid.
For a claim made under our warranty written certification of your installers
credentials can be required. For further information or to find a qualified
installer in your area please visit the Institute of Plumbers website - www.
iphe.org.uk
It is advised that all doors and drawers are removed prior to fitting to avoid
unnecessary damage occurring.
It is recommended that the furniture and accessories are installed after
tiling, ensuring that the product is installed flat to the tile face and allows
product to be easily removed if required in the future.
This document has been prepared for your guidance, you must exercise
due care at all times.
Please note that some units are heavy. Always take care when lifting, and
follow health and safety guidelines. It is recommended that 2 people carry
out the installation of larger basin/vanity units over 30Kgs gross weight.
Warning!
Please check for any hidden pipes or electrical cables before
dri lling holes in the floor or walls.
When using power tools always follow the manufacturer’s user instruc-
tions.
This installation guide details fitting to a solid wall. If your bathroom has
studded/plasterboard walls, please use appropriate plasterboard fixings.
Please ensure the wall can take weight of units detailed above. Before ins-
talling a wooden bathroom unit into a new property, extension or recently
plastered room we strongly advise the building/room is completely dry, well
ventilated and adequately heated.
Important pre-installation notes
To ensure full working use of the drawers we recommend the use of basin
furniture trap BTR0410W.
Care & Cleaning
Cast mineral marble and thermal glass products should be cleaned regular-
ly with warm soapy water, then rinsed with clean water and, if desired, dried
and polished with a soft cloth. Lime scale deposits can be removed using a
50:50 solution of warm water and lime scale remover and soft clean cloth.
We recommend regular cleaning with Cream Polish SD150RW, specially
formulated to clean and help protect the surface of cast mineral marble
basins.
Do not use abrasive cleaners or bleach in this will permanently damage the
surface of basins and furniture.
Use ONLY a well wrung chamois leather or micro fibre cloth to clean furni
-
ture carcasses. Real wood veneer carcasses should be wiped down after
use, avoid leaving water on the carcass for long periods.
If any maintenance is required then it must be carried out by a qualified
Plumber.
The manufacturer reserves the right to make technical modifications wi
-
thout prior notice.
INSTALLATION INSTRUCTIONS
1