Cross Technologies 2016-26 Скачать руководство пользователя страница 10

Страница: 10 / 18

2.3 Front Panel Controls and Indicators - The following are the front panel controls and indicators.

MENU

EXECUTE

F = 2050 G = +10.0

REMOTE

POWER

LCD DISPLAY
Display shows frequency in MHz and Gain
in dB, and is used to change settings in
Program mode.

S1 - MENU/EXECUTE BUTTON
Press this to get into Program mode
and to execute any changes.

DS6 - POWER LED
Green LED indicates
presence of DC power.

DS1 - REMOTE LED
Yellow LED indicates
remote operation.

S2 - VERT. TOGGLE
Vertical toggle switch that controls
values in the Menu items when in
program mode. Does not function in
the normal display mode.

S3 - HORIZ. TOGGLE
Horizontal toggle switch that
controls which values are being
adjusted. Does not function in the
normal display mode.

ALARM

DS3 - ALARM LED
Red LED indicates
downconverter alarm.

FIGURE 2.3 2016-26 Front Panel Controls and Indicators

2016-26 Manual, Rev. A

Page 10

2/2/09

Содержание 2016-26



















Результаты поиска

Содержание 2016-26

Отзывы:

Похожие инструкции для 2016-26

Бренды по названию

Популярные бренды

Cross Technologies 2016-26, Инструкция по эксплуатации

Результаты поиска

Содержание 2016-26

Отзывы:

Похожие инструкции для 2016-26

Бренды по названию

Популярные бренды