background image

English

 

 

Platter Auto-stop  

If the 

Auto-stop Sw

i

tch

 is set to ON position, the platter will stop spinning 

automatically when the record plays to the end. In some rare occasion, if the 
turntable stops playing before the end of the record, set the switch to OFF 
position the turntable should overcome this issue. 
 
 

Adjustment if Tonearm Stops too early  

If the platter stops before the tonearm reaches the end of the record, you can 
adjust it by following the below steps: 
1.  Disconnect the turntable from the power supply. 
2.  Insert a screwdriver into the 

Auto-stop Adjustment Hole

 and locate the 

tuning screw inside. 

3.  If the tonearm stops earlier than the end of the record, rotate the screw 

clockwise by approximately ¼ turn only.  

4.  Reconnect the turntable to the power supply.  
5.  Replay the record to see if the adjustment has been successful. If not, repeat 

steps 1-4, but only rotate slightly to perform the fine adjustment. Rotate the 
screw counter-clockwise if the tone arm fails to stop. Repeat this fine 
adjustment process until the tonearm will stop at the correct finish point. 

 
 

Needle Replacement 

Removing Needle 

1.  Gently pull down the front edge of the needle. 
2.  Pull needle forward. 
3.  Pull out and remove. 

 

 
Installing Needle 

1.  Position the needle with its tip facing down. 
2.  Line up the back of the needle with the cartridge. 
3.  Insert the needle with its front end at a downward angle and gently lift the 

front of the needle upward until it snaps into place. 

 

 
 

Содержание CR6016A










Отзывы: