background image

 

OPERATING INSTRUCTIONS - ALARM 

 

Optional M.A.P. (Mobile Accessories Protection) 

This  system  can  be  programmed  to  provide  Crimestopper’s  unique  M.A.P.  (Mobile  Accessories  Protection) 
feature  that  allows  you  to  prevent  unauthorized  access  of  your  vehicles  Audio,  Cellular,  Navigation,  or 
Entertainment  systems.    This  feature  is  OPTIONAL  and  will  requires  extra  parts  and  labor  for  installation.  
Consult  your  installation  dealer  about  MAP  before  or  during  installation.    The  CS2011RS  must  be 
programmed  for  MAP  operation.   When  the  system  is  put  into  Valet  Park  mode,  M.A.P.  will  prevent  stereo, 
entertainment, navigation, or cellular system from being used. 

 
 
 

LED DIAGNOSTICS 

 

The CS-2011DP system includes disarm diagnostics, through the RED LED light, that will help in determining 
what caused the last trigger of the alarm system.  This is a valuable tool in determining how the vehicle was 
tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to 
correct the problem.  When the system is disarmed with the remote you will hear the normal 2 chirps, then 4 
quick chirps that indicate the alarm was triggered while you were away.  Check the LED light for a sequence 
of flashes: 

 

Shock Sensor = 1 Flash 

Door = 2 Flashes      Hood/Trunk = 3 Flashes     Ignition = 4 Flashes 

 

Diagnostics will reset when the Ignition is turned on or when the system is re-armed. 

 
 
 

REMOTE ENGINE CONTROL 

 

REMOTE ENGINE STARTING - SUCCESSFUL START 

1)  Press and release the remote start button on the remote transmitter.  System will chirp 3 times for audible 

confirmation.  (Chirps can be programmed on or off-See Option programming in the installation manual.) 

2)  Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on. 
3)  After 6 seconds Starter Motor engages, Parking lights and Accessory circuits turn off while cranking. 
4)  Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock. 
5)  Engine will remain running for programmed run time until reset with Brake pedal.  If needed, the engine can 

be turned off with remote transmitter. 

 

 

Содержание Super Rage CS-2011DP

















Отзывы: