background image

 

13 

OPTION PROGRAMMING Cont. 

 

14. CARJACK FEATURES 

This option controls the unit’s Car Jack features.  Enable or Disable Carjack (Turn ON or OFF) with this option. 

 

15. Lock/Unlock or Arm/Disarm with Ignition ON 

This option allows you Arm and Disarm the system with the Ignition ON. This is used when there is a remote 
starter added to the system. The default is lock/unlock without arm and disarm while the ignition on. 

 

16. Data Port Protocol: 

This option controls the Data Port Protocol for 1-Way (OFA modules) or 2-Way  (SL modules). The default is 
set for 2-Way Protocol. This option has no effect on conventional wiring of Bypass modules. 

 

CUSTOM PERSONAL OVERRIDE CODE 

 

Custom override allows the user to set a specific number of button presses (2-15) required to perform an 
emergency override/disarm of the alarm system.  This increases the level of security of the system, but you 
MUST MEMORIZE how many button presses you have changed your system to use or the unit will not disarm 
in an emergency. 

 

1.  Enter programming mode. (See step #1 on page 9) 
2.  Press program button three times to go to option #3 “Passive Locks/Custom Override”. 
3.  Press both Buttons (1+2) on the remote transmitter (3 chirps). 
4.  Press and release the program again the number of times you desire in order to perform emergency disarm 

on this alarm system.  Press the program button 2-15 times only.  You need to wait for the siren to chirp the 
same number of times you pressed the program button to confirm. 

 

To test feature:  Trip the alarm system, turn key ON, press the program/valet button 2-15 times as 
programmed above then continue to HOLD DOWN valet button on the LAST PRESS for 5 seconds.  Alarm 
should disarm.  If system does not disarm, then disarm with the remote transmitter and try again.  If system 
still does not disarm or you have forgotten your custom code, then you must use your remote control to disarm 
the system 

 

CAUTIONARY NOTE! 

If you set up this feature and forget your special code, there is no way to disarm the system other than the 
remote control.   

 
 

Содержание CS-2000DPII TW2

























Отзывы: