background image

DO

 

GUIDE

DOC. 7791A (2047943) 11.16

Specifications subject to change without notice.

DO

 Commission the System

Using the web interface, configure the device. To access the web interface, open a web browser and enter either of the following:

hostname

/setup (

hostname

 is the hostname of the device)

or

xxx.xxx.xxx.xxx

/setup (

xxx.xxx.xxx.xxx

 is the IP address of the device)

The DMPS3-4K-200-C and DMPS3-4K-300-C also provide the built-in DMPS .AV Framework™ Base Program that enables complete system control 
without requiring additional programming. For complete details about the capabilities supported by the .AV Framework Base Program, go t

www.

crestron.com/avframework.

DO

 Route the Inputs

To route an input to one or more outputs, use the web interface or the front panel push button controls. 

To route the inputs using the front panel push button controls, do the following:

1. Press the 

ROUTE 

push putton.

2. Press the 

INPUT

 push button that corresponds to the input to be routed.

3. Press the desired 

OUTPUT

 push buttons to which the input is to be routed.

4. Press the 

ENTER

 push button.

* The DM INPUT and DM OUTPUT ports are PoDM+ PSE (Power Sourcing Equipment) ports and are HDBaseT PoE+ compatible. The CONTROL SUBNET port is a PoE PSE port.  
   Enabling PoDM+, HDBaseT PoE+, and PoE power sourcing requires connection of the PODM+ INPUT PWR port to an external Crestron power supply (PW-4830DUS or  
   DM-PSU-3X8-RPS). Any wiring that is connected to a PoDM+, HDBaseT PoE+, or PoE PSE port is for intrabuilding use only and should not be connected to a line that runs outside of  
   the building in which the PSE is located.

 

 

As of the date of manufacture, the product has been tested and found to comply with specifications for CE marking.

 

Federal Communications Commission (FCC) Compliance Statement 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

  Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

NOTE: 

 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 

against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may 
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference 
by one or more of the following measures:

 

• Reorient or relocate the receiving antenna.

 

• Increase the separation between the equipment and receiver.

 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

 

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada (IC) Compliance Statement 

CAN ICES-3(B)/NMB-3(B)

Rack Mounting Safety Precautions

 

Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient temperature. Therefore, consideration should be 
given to installing the equipment in an environment compatible with the maximum ambient temperature (Tma) specified by the manufacturer.

 

Reduced Airflow:  Installation of the equipment in a rack should be such that the amount of airflow required for safe operation of the equipment is not compromised.

 

Mechanical Loading:  Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

 

Circuit Overloading:  Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits might have on overcurrent protection and supply wiring. Appropriate consideration 
of equipment nameplate ratings should be used when addressing this concern.

 

Reliable Earthing:  Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuit (e.g., use of power strips).

Electrical Connection

 

“This product must be connected to an earthed mains socket-outlet.”

 

Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.” 

 

Norway: “Apparatet må tilkoples jordet stikkontakt.” 

 

Sweden: “Apparaten skall anslutas till jordat uttag.”  

The specific patents that cover Crestron products are listed at 

http://www.crestron.com/legal/patents

The product warranty can be found a

www.crestron.com/warranty

.

Certain Crestron products contain open source software. For specific information, please visit 

www.crestron.com/opensource

Crestron, the Crestron logo, .AV Framework, 3-Series, Cresnet, Crestron Toolbox, DigitalMedia, DM, and DM 8G+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. HDBaseT and the HDBaseT Alliance logo are either trademarks 
or registered trademarks of the HDBaseT Alliance in the United States and/or other countries. HDMI and the HDMI logo are either trademarks or registered trademarks of HDMI Licensing LLC in the United States and/or other countries. Other trademarks, registered trademarks, and trade names 
may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron. 
©2016 Crestron Electronics, Inc.

DO

 Learn More

Visit the website for additional information and the latest firmware updates. To learn more about this product, use a QR reader  
application on your mobile device to scan the QR image.

Crestron Electronics

 

15 Volvo Drive, Rockleigh, NJ 07647 
888.CRESTRON | www.crestron.com

DMPS3-4K-200-C

DMPS3-4K-300-C

Отзывы: