Crestron CLW-DIM1, Руководство по эксплуатации

Страница: 6 / 44

infiNET™ Dimmers Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF
C2N-MNETRPT infiNET Repeaters) can communicate with one C2N-MNETGW
infiNET Gateway and, if more devices are needed, more C2N-MNETGW gateways
may be added to a Cresnet
®
network.
Crestron infiNET dimmers operate on the 2.4 GHz “ISM band” (2400 MHz to
2483.6 MHz) at 10 mW. The output power of these devices allow RF signals to
travel approximately 150 feet indoors and 250 feet outdoors (subject to site-specific
conditions) without the use of repeaters or other infiNET devices. The range is
dependent on construction of the building, obstructions, and RF interference from
other devices. The location of the dimmer is an important factor in determining RF
performance. Adding more infiNET devices or repeaters to the network effectively
increases the range, strength, and reliability of the network.
The -DIM1RF and -DIM4RF feature a three-position mode selection switch. Refer to
“Operation” on page 9 for more information. In the absence of control system
communications, the dimmer can still be used to control the attached load.
The CLW-DIMS1RF (-DIMS1RF) and CLW-DIMS4RF (-DIMS4RF) are similar to
the -DIM1RF and -DIM4RF (respectively) with the added capability of working with
one or more slave units (CLW-SLVD1RF) in a multi-dimmer / single circuit
application. For more information, refer to the latest version of the infiNET Dimmers
Installation Guide (Doc. 6292) which is available from the Crestron website
(www.crestron.com/manuals).
The CLW-SLVD1RF (-SLVD1RF) is a slave unit that when used in conjunction
with the -DIMS1RF or -DIMS4RF acts as an additional dimmer control point in a
multi-dimmer / single circuit application. It does not connect to an infiNET system
and cannot be used without a -DIMS1RF or -DIMS4RF. The -SLVD1RF does not
have a mode selection switch. It can only be programmed when used in conjunction
with a -DIMS4RF (refer to “Attaching and Detaching the Electrical Load” on page
27). Otherwise, it will emulate the
RUN mode of the -DIMS1RF (even if connected
to a -DIMS4RF) unless the mode selection switch of the master is set to “OFF”.
These dimmers can be ordered with custom engraved buttons already installed by
Crestron. Engraved buttons cannot be installed or changed in the field. Contact
Crestron for more information.
These dimmers are available in white, almond, and black. White units are designated
by part numbers ending in “W”. Almond units are designated by part numbers
ending in “A”. Black units are designated by part numbers ending in “B”. Each
dimmer can be covered with a decorative faceplate (not supplied).
For installation instructions, refer to the latest version of the infiNET Dimmers
Installation Guide (Doc. 6292), which is available from the Crestron website.
Specifications
Following are specifications for the -DIM1RF, -DIM4RF, -DIMS1RF, -DIMS4RF,
and -SLVD1RF.
CLW-DIM1/4RF, CLW-DIMS1/4RF, & CLW-SLVD1RF Specifications
SPECIFICATION DETAILS
Power Requirements Line Power, 120 VAC, 60 Hz
Operating Frequency 2400 MHz to 2483.6 MHz
(802.15.4 compliant)
RF Output Power 10 mW
(continued on following page)
2
•
infiNET Dimmers: Crestron CLW-DIM1/4RF, -DIMS1/4RF, -SLVD1RF Operations Guide - DOC. 6396