CLW-SW1, SWS1, & SLVS1(W/A/B)
section 725-55, Part D of the 2002 National
Electric Code.
3. Wire the switches as shown in Figure 3 on
page 8.
NOTE:
Do not connect the BLUE (Slave) wire
to the Black (Hot) or RED (Load) wires.
3. Wire the switch as shown in Figure 1 on
page 8.
NOTE:
The RED (Load) and BLACK (Hot)
wires are #14 AWG. The BLUE (Slave) and
WHITE (Neutral) wires are #18 AWG. The
GREEN (Ground) wire is #16 AWG. The GRAY
(Cresnet) wires are #22 AWG. The BLACK wire
(Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
NOTE:
The RED (Load) and BLACK (Hot)
wires are #14 AWG. The BLUE (Slave) and
WHITE (Neutral) wires are #18 AWG. The
GREEN (Ground) wire is #16 AWG. The GRAY
(Cresnet) wires are #22 AWG. The BLACK wire
(Cresnet ground) paired with the GRAY
(Cresnet) wires is #22 AWG.
NOTE:
If a -SWS1 is installed without a
-SLVS1, the BLUE lead (Slave) should be
capped.
NOTE
: Since the -SWS1 is installed without a
-SLVS1, the BLUE lead (Slave) should be
capped.
NOTE:
The WHITE (Neutral) connection on
the -SLVS1 is optional and is only required for
operation of the LED. If the neutral is not
available, the white lead should be capped off.
Other Wiring
For another scenario that may be encountered
during installation, refer to Figure 2 on page 8.
4. Splice the gray wires of the -SW1 or -SWS1 to
the Class 2 low voltage wires connected to the
Crestron control system or a Crestron connection
block device. Push the wires and the splices into
a hole in the drywall to provide the necessary
separation.
4. Splice the gray wires of the -SWS1 to the Class 2
low voltage wires connected to the Crestron
control system or a Crestron connection block
device. Push the wires and the splices into a hole
in the drywall to provide the necessary
separation.
5. Push all power wires back into the wallbox and
fasten the device to the wallbox with the
provided screws.
5. Push all power wires back into the wallbox and
fasten the devices to their respective wallboxes
with the provided screws.
6. Attach decorative faceplate.
6. Attach
decorative faceplates.
7. Restore power at the circuit breaker.
7. Restore power at the circuit breaker.
Wiring a -SWS1 with One or More
-SLVS1s
Operation
NOTE:
The -SWS1 must be installed in the same
wallbox that contains the connections to the load.
The -SW1, -SWS1, and -SLVS1 have one large
pushbutton. The -SW1 and -SWS1 also have a three-
position mode selection switch. The function of the
pushbutton is determined by the position of the mode
selection switch. Refer to the following diagram.
The following describes installation of a -SWS1 master
with a -SLVS1 slave.
1. Turn power off at the circuit breaker.
NOTE:
The -SLVS1 does not have a mode selection
switch. It emulates the operation of the -SWS1 to which it
is connected unless the mode selection switch of the
master is set to “OFF”.
2. Pull Class 2 low voltage wires through a hole in
the drywall located outside of the electrical box,
to the Crestron control system or a Crestron
connection block device. Leave wires outside of
the wallbox for connection to the -SW1 or
-SWS1.
NOTE:
Alternate wiring methods may be used
for the Class 2 wiring connection. Refer to
section 725-55, Part D of the 2002 National
Electric Code.
Installation Guide – DOC. 6251A
Stand Alone Wall Box Dimmer: CLW-SW1, SWS1, & SLVS1
•
5
