v. 1.0 5/14/97 C3400006
Crest Audio Inc.
100 Eisenhower Dr., Paramus NJ 07652 USA
TEL
: 201.909.8700
FAX
: 201.909.8744
http://www.crestaudio.com
Printed in USA
H D 1 8 P O W E R A M P L I F I E R
S P E C I F I C AT I O N S
Rear View
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á
L'HUMIDITÉ
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR
CAUTION
A
A B
A B
A
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
PUSH
PUSH
A
B
B
A
+
+
+
A
A
B
B
Output Power
@4
Ω
/Ch
120V
~
60 Hz
30A
HD 18
1800W
+
XLR Pin +
2 3
A
B
1
3
2
GAIN
Ø
dBu
40x 20x
Power figures are watts per chan-
nel, both channels driven.
Crest Audio reserves the right to
make improvements in manufac-
turing or design which may affect
specification.
Crest Audio specification litera-
ture is available in downloadable
PDF format; visit our website at:
http://www.crestaudio.com.
©1997 Crest Audio Inc.
1kHz, 0.03% THD+N
20Hz-20kHz, 0.1% THD+N
1000W
950W
1800W
1700W
2500W
2400W
3600W
3400W
5000W
4800W
99V
140V
20Hz-20kHz, -3dB@150kHz
20Hz-20kHz, -.2dB/+.2dB
ACL, IGM, AutoRamp, short circuit, DC voltage,
turn-on/off transient, current inrush, sub/ultrasonic input.
<0.03%
<0.01%
25V/
µ
s
800:1
> - 70dB
.775V standard (switchable; see table below)
X115 standard (switchable; see table below)
>20k
Ω
/>10k
Ω
-115dB
> - 80dB
H
Female XLR (pin 2+, switchable for pin 3+), TRS (tip+)
2 pair of 5-way output binding posts
144,000
µ
F
100V-240V, 50-60Hz
3.0A
12.0A
25.0A
36.0A
7125 BTU/hr
9450 BTU/hr
Back-to-front via 2 rear panel mounted variable-speed DC fans
(filters removable without tools)
Front Panel: 2 attenuators; Rear Panel Switches: signal ground lift,
mode select, gain select, XLR input pin 2/3 hot (+)
Clip/Limit, Signal, Temp/DC, Active
Steel chassis, 16 gauge. Double thickness in rack ear areas.
5.25" x 19" x 18" / 133 x 483 x 457mm
82 lbs. (37.23 kg.), 77 lbs. (34.96 kg.)
3 years
8
Ω
Stereo Power
4
Ω
Stereo Power
2
Ω
Stereo Power
8
Ω
Bridged Mono Power
4
Ω
Bridged Mono Power
Max RMS Output Voltage
(each channel)
Peak Output Voltage
(each channel)
Frequency Response
(+0 / -0.3dB, 1W/8
Ω
)
Power Bandwidth
(rated power at 4
Ω
, 1% THD+N)
TourClass
®
Protection
THD+N
(rated power at 4
Ω
, 1kHz)
SMPTE IMD
(rated power at 8
Ω
, 60Hz & 7kHz)
Slew Rate
Damping Factor
(10-400Hz at 8
Ω
)
Input CMRR
(1kHz)
Input Sensitivity
(rated power at 8
Ω
)
Voltage Gain
Input Impedance (balanced/unbalanced)
Hum and Noise
(“A” weighted, full power, 4
Ω
)
Crosstalk
(“A” weighted, full power, 4
Ω
)
Class
Input Connectors
(per channel)
Output Connectors
(per channel)
Filter Storage
Power Supply
(factory configured)
Idle Current Draw 120V
1/8 Power Curr. Draw
(typical music, 120V/4
Ω
)
1/3 Power Curr. Draw
(continuous music, 120V/4
Ω
)
Max Curr. Draw
(circuit breaker rating, 120V/4
Ω
)
Thermal Emissions
(1/8 Power, 4
Ω
)
Thermal Emissions
(1/3 Power, 4
Ω
)
Cooling
Controls
LED Indicators
(per channel)
Construction
Dimensions
(Height x Width x Depth)
Gross Weight, Net Weight
Warranty
Gain
Sens
Gain/Sensitivity Options
Factory Standard
X115
.775V
Option 1
X40
2.24V
Option 2
X20
4.47V
Architect’s & Engineer’s Specifications
The power amplifier shall have two channels. At 8 ohms, 20Hz
- 20kHz, 0.1% THD+N, it shall deliver a minimum of 950 watts
per channel. At 4 ohms, 20Hz - 20kHz, 0.1% THD+N, it shall
deliver a minimum of 1700 watts per channel. In bridged mono
mode with an 8 ohm load, 20Hz - 20kHz, 0.1% THD+N, it
shall deliver a minimum of 3400 watts.
The amplifier shall have circuitry to protect itself from output
short circuits, thermal overload or other adverse load condi-
tions. The amplifier shall protect speaker loads from DC volt-
age on outputs. The amplifier shall have active clip limiting
and impedance sensing circuitry. Output relays shall protect
the speakers from amplifier failure.
Two rear panel mounted variable speed DC fans (filters
detachable without tools) shall provide back to front air flow
through the chassis.
Each channel shall have a standard (factory-set) input sensitiv-
ity of .775 volt, and shall be fitted with an external switch
which allows the gain to be altered to X20 or X40. The hum
and noise level shall be 115 dB below rated output, “A”
weighted. SMPTE IMD shall be less than 0.01% at rated
power, 60Hz and 7kHz. The amplifier shall have a class H out-
put stage. The frequency response shall be 20Hz-20kHz, +0,
-0.3dB (1W 8
Ω
).
The amplifier will operate at 100V-240V, 50-60 Hz AC (config-
ured at factory). Maximum current draw shall not exceed 36
amperes at 120VAC (limited by front panel breaker).
Front panel indicators shall include Active, Protect, Signal,
and Clip LED’s for each channel. Front panel attenuators
shall be recessed and detented.
Rear panel input connectors shall be female TRS, and XLR
type, rear-panel switchable for pin 2 (factory setting) or pin 3
positive. Output terminations shall be 2 pair of 5-way output
binding posts. Rear panel switches for ground lift,
Stereo/Parallel/Bridged Mono mode, XLR polarity and gain
selection shall also be provided.
A rear-panel single AC mains cord having an appropriate AC
plug for the intended operating voltage shall be provided ..
The packaging of the amplifier shall allow for standard rack
mounting without requiring space between similar units.
Optional rack mount handles will be available. Dimensions
shall be 19" (483mm) wide, 5.25" (133mm) high and 18"
(457mm) deep. The amplifier shall weigh 77 lbs. (34.96 kg.)
net, and shall be designated the Crest Audio model HD18 .
C3400006