(A) 4 Mounting collars,
(B) 4 Rail seats,
(C) 4 Inner wall bracket sleeve,
(D) 4 Outer wall bracket sleeve,
(E) 4 Position locking screws,
(F) 4 Wall plugs,
(G) 4 Wall mounting screws,
Procedure for wall mounting
Wall mounting dimensions:
mm
Step 1
Mark suitable mounting hole positions for the fixing brackets (ensuring
they are horizontal) - see
Fig. 3
, ensure to allow enough room above
and below to maintain the minimum clearance stated in
Fig. 1
.
Step 2
Drill and plug (F) the wall to suit. Fix the outer wall bracket sleeve (D) to
the wall using the screws provided (G). Ensure to align the bracket so
that the fixing hole is accessable once the towel rail is fitted - see
Fig. 4
.
Note: we recommend that the fixing hole is positioned horizontally,
towards the side of the towel rail. This will allow easy access with a
screw driver when fixing the rail in its final position.
Step 3
Carefully assemble the four mounting collars (A) and rail seats (B) to
the towel rail and secure in the positions by inserting and turning the
inner bracket sleeve (C) through 90 degrees as shown
in
Fig. 5
. The
brackets should be placed on the bottom and second from top rails and
separated by a distance of 360mm.
Ensure the inner bracket sleeves
are facing directly backwards.
Fig. 3
Model
Y (mm)
CLR5
300
CLR7
500
CLR10
800
CLR12
1000
Fig. 4
General
The towel rail is designed to provide an all year round service for
airing towels and articles of clothing. It is not intended to provide a
sole heating service, but will take the chill off a small
size bathroom,
lavatory or en suite.
No routine maintenance is necessary apart from occasional cleaning.
The unit is splashproof to IPX5 standard.
Electrical
WARNING - This appliance must be earthed
The electrical installation of this towel rail must be carried out by a
competent electrician in accordance with the current I.E.E Regulations.
The towel rail is suitable for use on an A.C.~ electrical supply. Before
installation check that the supply voltage corresponds with that marked
on the rail.
IMPORTANT -
The wires in the mains lead are coloured in
accordance with the following code:
BLUE
-
NEUTRAL
BROWN
-
LIVE
GREEN/ YELLOW
-
EARTH
As the colours of the wires in the mains lead of this
appliance may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN and YELLOW must be
connected to the terminal in the plug which is marked with the letter
E
or by the earth symbol
or coloured green or green and yellow.
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter
N
or coloured black.
The wire which is coloured BROWN must be connected to the terminal
which is marked with the letter
L
or coloured red.
This appliance must only be used on A.C. mains supply of 230/240
Volts~.
Installation
If fitted in a room containing a bath or shower, to comply with the current
I.E.E. Regulations, a cable outlet will be necessary with the supply
to the heater controlled by a double-pole pull-cord switch having a
contact separation of 3mm in each pole. The body of the switch should
be situated as to be normally inaccessible to a person using a bath or
shower. Alternatively the switch can be located outside of the bathroom.
IMPORTANT
-
Protect the electrical connection whilst
handling the towel rail.
The towel rail must be permanently fixed to the wall using the wall
brackets supplied.
WARNING
-
to ensure safe, correct operation the rail must only
be mounted vertically as shown in
Fig. 1
, observing the minimum
clearances stated.
WARNING - The towel rail is heavy. Care must be taken when
lifting and fitting the towel rail.
Wall mounting
The wall mounting accessory pack contains the following:
Fig. 2
Fig. 5
