6
c) ELECTRICAL
WARNING: THIS SHOWER MUST BE EARTHED.
The electrical installation must be in accordance with the current BS.7671 (IEE Wiring Regulations)
and “Part P” of the Building Regulations and/or local regulations.
1.
The shower unit is designed for a single phase AC electrical supply.
Please check the rating plate on the unit to see what details apply to your shower.
AS A
GUIDE ONLY (* Only applies if external earth impedance is less than 0.35 Ohms)
Rating
Cable Sizes
Fuse / MCB
Cable Length
6.0mm²
10.0mm²
40A Type B MCB
27m Max.
45m Max.
8.5 / 7.8kW 240 / 230V
6.0mm²
10.0mm²
45A BS.1361 fuse
12m Max.
*
21m Max.
*
6.0mm²
10.0mm²
40A Type B MCB
27m Max.
45m Max.
9.5 / 8.7kW 240 / 230V
6.0mm²
10.0mm²
45A BS.1361 fuse
12m Max.
*
21m Max.
*
10.5 / 9.6kW 240 / 230V
10.0mm²
45A BS.1361 fuse
12m Max.
*
Remember to upgrade the cable if it runs in thermal insulation in a loft, or for a longer distance.
2.
A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with
the wiring rules. We recommend a ceiling switch mounted in a convenient position.
3.
If you have decided to connect the cable on the left hand side then please remove and use the
cable clamp that was provided along the right side (see Diagram 3).
WARNING: IF LEFT HAND SIDE CABLE ENTRY IS USED, THE MAINS CABLE OUTER SHEATH
MUST BE STRIPPED BACK TO THE LEVEL MARKED ON THE BACKPLATE, AND ALL
THREE CONDUCTORS MUST BE FULLY SLEEVED WITH THE SLEEVING PROVIDED
BETWEEN THERE AND THE TERMINAL BLOCK (SEE DIAGRAM 3a).
4.
Connect cable to terminal block making sure that all the retaining screws are
VERY
TIGHT
and that
no cable insulation is trapped under the screws.
WARNING: FAILURE TO COMPLY WITH THESE INSTRUCTIONS COULD RESULT IN FAILURE
OF THE TERMINAL BLOCK.
5.
Re-fit the detachable bottom section with the two screws if it was removed.
11
SELF HELP
If the shower is not working satisfactorily, make the following checks before calling out the installer.
Any one of these adjustments could restore the performance.
The shower cycles
from HOT to COLD
The shower temperature is set too hot causing the thermal cut-out (safety
device) to operate.
Turn knob “C” clockwise
to increase water flow.
Slowly increase the water temperature by turning knob “C” anti-clockwise until a
comfortable showering temperature has been reached.
You MUST WAIT approximately 20 seconds for each adjustment to affect the
water temperature.
“Med (medium) / ” setting may need to be selected.
Water too HOT
Increase water flow by adjusting knob “C” clockwise.
“Med (medium) / ” setting may need to be selected.
Increase pressure to water supply e.g. fully open service valve or stop cock.
Check hose is not kinked restricting the water flow and clean handset.
Water too COLD
Check power is on by neon indicator being illuminated.
Decrease water flow by adjusting knob “C” anti-clockwise.
“High /
” setting may need to be selected.
Select inner or outer only handset spray pattern.
Spray pattern poor Clean the shower handset.
Water takes longer
to heat up
Thermal cut-out has operated after previous use and the neon indicator has
gone out (automatically resets when unit cools down)
“High /
” setting may need to be selected.
Water goes cold
while using
shower
Check neon indicator is illuminated.
Check water pressure has not fallen so far as to let pressure switch cut out,
e.g. Another tap drawing water off.
Raise position of shower handset.
Broken parts
Please contact our spares department on 0870 9000 420 (UK only).
Fitting instructions are provided with most spares
Water continues to
flow when button
“B” pressed to stop
This is normal for 10.5kW models only (Other models contact “After Sales”)
The shower includes a shutdown feature that means the water will continue to
flow for up to 7 seconds after “ (stop)” has been selected.
Please Note:- The fitting of Spare Parts must be supervised by a suitably qualified person.
White 2.0m Shower Hose
Cat No. 83792578
Cover
Contemporary
White
Cat No. 93590348
Chrome 1.25m Shower Hose Cat No. 93797641
Cover
Contemporary
Colour
Cat No. 93590349
WRAS Listed Water
Cover
Heritage
Cat No. 93590350
Isolating Valve
Cat No. 93792452
Thermal Cut-Out 50/88°C
Cat No. 93597871
Chrome Standard Accs
Cat No. 83595317
Solenoid Valve
Cat No. 93590355
Chrome Multi-Mode Accs
Cat No. 83595318
Backplate Lower Section
Cat No. 93590356
Chrome Curved Accessories Cat No. 83595320
PRV Outlet Body Assy
Cat No. 93590357
Curtain and Rail Pack
Cat No. 83792812
Flexible Outlet Pipe c/w Clip
Cat No. 93590358
Curtain and Rail Pack with
Tank Clip
Cat No. 93590715
Non-Slip Mat
Cat No. 83792811
PRV Washer
Cat No. 93795817
Cylinder “O”-Ring
Cat No. 93795809
Handset -
Contemporary
Cat No. 93597864
Height Adjuster -
Contemporary
Cat No. 93597861
Handset -
Heritage
Cat No. 93593571
Height Adjuster -
Heritage
Cat No. 93590361
WHAT TO DO IF THINGS GO WRONG (1)
ADDITIONAL ACCESSORIES COMMON SPARE PARTS
Additional accessories and spare parts
can be supplied against any
Credit or Debit cards from
Creda Sales Hotline 0870 9000 420
