Assembly
© Copyright 2014, Creative Playthings, Printed in U.S.A.
60081-102 SWING BEAM
19860-100 Rev D (04-18)
Page 2
ASSEMBLY INSTRUCTIONS
STEP 1 – Assemble Beam:
Set the Beam Assembly so the edge with holes faces up.
Secure the two rails of the Beam Assembly (D) using eight
1/4 x 3" Hex bolts, 1/4" Lock Washers, 1/4" Flat Washers
and 1/4" Weld Nuts, as shown.
STEP 3 – Swing Hangers:
Insert the screw end of one Swing Hanger through a 5/16" flat washer and into one of the holes on the bottom surface of
the Swing Beam. Use a screwdriver for leverage while turning the Swing Hanger into the wood. The connector must be
screwed into the wood fully, with the bend of the shaft resting firmly against the 5/16" flat washer. Repeat with the other
Swing Hangers.
It is extremely important that you align each Swing Hanger in the proper position as shown in the illustrations. The swing
motion must be perpendicular to the Beam.
CAUTION: If these installation instructions are not explicitly followed, the Swing Hanger shaft will break or pull out of the
wood and injuries will result.
Screw-type Swing
Hangers
We have packaged more hardware than is required for assembly.
A 1 33689-102 Back Upright 2 x 4 x 46"
B 1 33690-102 Front Upright 2 x 4 x 40-11/16"
C 1 33957-102 Horiz. Support 2 x 4 x 36-3/4"
D 1 40572-102 Beam Assembly
E 2 40581-102 Leg Assembly
F 2 36515-102 Ground Stake
G 1 14099-400 6" Triangle Plate, Green
H 1 14100-400 6" L-Brace, Green
50537-201 2 Swings 1 Trap Pack
J 2 40577-400 Sling Swing
K 1 40578-104 Ring Trapeze
50105-700 Swing Hanger 6 Pack
6 12002-206 Flat Washer 5/16"
6 17004-100 NyGlide Swing Hanger
50532-707 1/4" Hardware Bag
19 17001-104 Weld Nut 1/4"
20 12002-205 Flat Washer 1/4"
19 12017-205 Lock Washer 1/4"
5 17020-109 Screw #8 x 2-1/2"
18 17003-1209 Hex Bolt 1/4 x 3"
1 17036-1201 Lag Screw 1/4 x 3"
50532-702 5/16" Hardware Bag
10 17001-105 Weld Nut 5/16"
19 12002-206 Flat Washer 5/16"
7 12017-206 Lock Washer 5/16"
1 17003-611 Hex Bolt 5/16 x 1-1/2"
4 17003-1211 Hex Bolt 5/16 x 3"
3 17003-1811 Hex Bolt 5/16 x 4-1/2"
2 17003-2211 Hex Bolt 5/16 x 5-1/2"
PARTS
STEP 2 – Assemble Legs:
Secure the two rails of the one Legs Assembly (E) using
four 1/4 x 3" Hex Bolts, 1/4" Lock Washers, 1/4" Flat Wash-
ers and 1/4" Weld Nuts, as shown. Repeat the other Leg
Assembly.
D
E
