cre8audio NiftyCASE Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 13

background image

Installing modules

Always turn off NiftyCASE before adding or removing modules.

Handling modules that are powered can lead to damage.

Observe the following picture for the correct cable orientation. The red line on the
cables should always match (facing down).

Use the supplied tool to remove and replace the screws.
NiftyCASE uses M3 (3mm) thread screws.

«
1
2
3
4
...
»

Содержание NiftyCASE














Отзывы:

Нет отзывов

Похожие инструкции для NiftyCASE

Бренд: Sagola Страницы: 8

Бренд: Raymarine Страницы: 90

Бренд: Panlux Страницы: 2

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренд: M-Audio Страницы: 4

Бренд: M-Audio Страницы: 52

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренд: Ultraflex Страницы: 48

Бренд: U-Line Страницы: 9

Green Machine H-3518

Бренд: U-Line Страницы: 3

Бренд: Garmin Страницы: 2

Бренд: Parker Страницы: 58

Бренд: ABB Страницы: 154

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды