background image

Smartwasher 

SW-37

Operating Manual

5

Installation & Setup Continued

OzzyMat

®

 FL-4 Maintenance

1.

Make sure the pump is not running.

2.

Remove the False Bottom from the sink.

3.

Peel away the top layer of the OzzyMat

®

 and wring out

any excess fluid. Then, dispose of this layer according to
your local regulations.

4.

Return the False Bottom to its proper place.

Replacing the OzzyMat

®

1.

Make sure the pump is not running.

2.

Remove the False Bottom from the sink.

3.

Remove the last layer of the soiled OzzyMat

®

 and set to

one side of the filter support grid.

4.

Remove a new OzzyMat

®

 from its poly bag, unfold the mat

and lay it on top of the filter support grid - white side up.

5.

 

Roll up used OzzyMat

® 

and stand vertically against the

side of the sink to drain excess fluid. This will allow good
fluid to drain from used mat before disposal. Never wring
out OzzyMat

® 

prior to disposal.

6.

Take the old, used OzzyMat

®

 and place into the poly bag

the new mat came in.

7.

Return the False Bottom to its proper position.

8.

Discard used OzzyMat

®

 in accordance with your local

regulations.

OzzyJuice

®

 Degreasing Solution

The SmartWasher

®

 uses a specially formulated fluid which

provides a combination of excellent cleaning characteristics,
safety and nutrition for the Ozzy

®

 microbes. OzzyJuice

®

 is

provided in ready-to-use containers.

Adding OzzyJuice

®

Slowly pour a full container of 
OzzyJuice

®

 directly into the

SmartWasher

®

 sink. The “Add 

Fluid” light should go out when 
you have completed this process.

To help monitor and maintain 
the proper fluid level, the 
SmartWasher

®

 is equipped with 

an “Add Fluid Light”.
When the “Add Fluid” light comes 
on the heater in the unit will turn 
off until an ENTIRE 20L container 
of OzzyJuice

®

 is added.

The “Add Fluid” light will shut off 
and the heater will come back on once the 20L container of 
OzzyJuice

®

 is added to the SmartWasher

®

.

Temperature Settings

Your SmartWasher

®

 should be plugged in 24 hours a day, 

7 days a week to maintain optimal temperature.

Depending on the OzzyJuice

®

 solution shipped with your 

SmartWasher

®

, the thermostat is factory-set to maintain fluid 

temperature between 40°C to 46°C (+/-1°). This temperature 
provides the optimum condition for effective cleaning and 
activity of Ozzy

®

 microbes.

The heater will not operate when the fluid level becomes 
critically low. Lift the sink and check your fluid level. When 
the “Add Fluid Light” illuminates add 1 (20L) container of 
OzzyJuice

®

. If, after a reasonable warm-up period, the fluid 

temperature seems too hot or too cold, please refer to the 
“Troubleshooting” section on page 10 and 11.

If the temperature falls below the recommended minimum, 
the system will still clean, but remediation of the hydrocarbons 
by the Ozzy

®

 microbe colony will slow down. However, the 

microbes will not die. The Ozzy

®

 colony will become more 

active when the fluid temperature reaches the appropriate 
level.

DO NOT ADD

Water, Solvent, Mineral Spirits, Gasoline or
Kerosene to your SmartWasher

®.

View the “How To” videos on the CRC SmartWasher

® 

machine set up and 

maintenance at www.crcind.com.au/smartwasher

For technical support visit our website www.crcind.com.au/smartwasher or call us on 1800 224 227

 

Содержание Smartwasher SW-37
















Отзывы: