Crane Weinman B Series Скачать руководство пользователя | Manualshive

Страница: 15 / 16

background image

Submersible Pumps

Resistance of cable and pump motor (measured at pump control):
Red-Black:_______Ohms(

Ω

) Red-White:_______Ohms(

Ω

) White-Black:_______Ohms(

Ω

)

Resistance of Ground Circuit between Control Panel and outside of pump: __________Ohms(

Ω

)

MEG Ohms check of insulation:
Red to Ground: _________ White to Ground: __________ Black to Ground: ____________

Operational Checks

Is there noise or vibration present?   YES___ NO___  Source of noise/vibration: ___________
Does check valve operate properly?   YES___ NO___ N/A___
Is system free of leaks?   YES___ NO___

Leaks at: ______________________________

Does system appear to operate at design

fl

ow rate? YES___ NO___

Nominal Voltage: _____________________ Phase: 1Ø 3Ø (select one)
Voltage Reading at panel connection, Pump OFF: L1, L2  _____   L2, L3 ____   L1, L3 _____
Voltage Reading at panel connection, Pump ON: L1, L2  ______  L2, L3 ____   L1, L3 _____
Amperage Draw, Pump ON:   L1 ____________

L2 _____________

L3 _____________

Submersible Pumps

Are BAF and guide rails level / plumb?   YES___ NO___
Is pump seated on discharge properly?   YES___ NO___
Are level controls installed away from turbulence?   YES___ NO___
Is level control operating properly?   YES___ NO___

Is pump fully submerged during operation? YES___ NO___

Follow up/Corrective Action Required

YES___ NO___

Additional Comments:

____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________
____________________________________________________________________________

Startup performed by: _____________________ Date: ______________________________

Present at Start-Up

( ) Engineer: ____________________________ ( ) Operator: ________________________

( ) Contactor: ____________________________ ( ) Other: ___________________________

All parties should retain a copy of this report for future trouble shooting/reference

A Crane Co. Company

420 Third Street

83 West Drive, Brampton

Piqua, Ohio 45356

Ontario, Canada L6T 2J6

Phone: (937) 778-8947

Phone: (905) 457-6223

Fax: (937) 773-7157

Fax: (905) 457-2650

www.cranepumps.com

«
...
13
14
15
16
»

Содержание Weinman B Series

















Отзывы:

Нет отзывов

Похожие инструкции для Weinman B Series

Бренд: Barnes Страницы: 12

Бренд: Walrus Страницы: 6

Бренд: Walrus Страницы: 4

VRV IV-S Series

Бренд: Daikin Страницы: 536

Бренд: Daikin Страницы: 226

Бренд: A.O. Smith Страницы: 6

Бренд: Junkers Страницы: 12

Бренд: Mixtron Страницы: 44

Бренд: ICI Caldaie Страницы: 48

Бренд: T.I.P. Страницы: 104

Бренд: Jandy Страницы: 24

Masterflex L/S 7569-00

Бренд: Cole Parmer Страницы: 8

Бренд: Graco Страницы: 46

Бренд: Barnstead Thermolyne Corporation Страницы: 32

Бренд: Champion Страницы: 27

Бренд: Trotec Страницы: 18

PWS BEV-300 Series

Бренд: Pure Water Страницы: 35

Hydra-Cat H.P. King

Бренд: Graco Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды