Crane PROSSER PUPP512 Series страница 4 Скачать руководство пользователя

Страница: 4 / 16

SECTION: A- PUMP SPECIFICATIONS

DISCHARGE:

2" (50.8mm) NPT (M), Vertical

VOLUTE:

Aluminum.

MOTOR HOUSING:

Aluminum.

IMPELLER:

Design:

3 Vane, Semi-open, Dynamically
Balanced.

Material:

Cast Iron ASTM A-48.

SHAFT:

416 Stainless Steel.

SQUARE RINGS:

Buna-N

HARDWARE:

300 Series Stainless Steel.

PAINT:

Air Dry Enamel.

SEAL:

Design:

Double Mechanical, Oil-Filled
Reservoir.

Material:
Pump End:

Rotating Face - Silicon Carbide
Stationary Face - Silicon Carbide

Motor End:

Rotating Face - Carbon
Stationary Face - Ceramic
Elastomer - Buna-N
Hardware - 300 Series Stainless

CORD ENTRY:

20 ft. Cord w/Plug. Molded in
Strain Relief And Compression
Seal.

SPEED:

3450RPM (Nominal).

MOTOR:

Design:

NEMA Design N-Single Phase,
Completely Oil-Filled.

Insulation:

Class

SINGLE PHASE:

Permanent Split Capacitor (PSC).
Includes Overload Protection
In Motor.

STRAINER:

.25" (6.4mm) Openings, with
Base Plate, Steel.

LIFTING HANDLE:

Thermoplastic

PUMP:

WEIGHT:

PUPP512

36lbs./16.3kg

13.00

(330.2mm)

16.38

(416mm)

3.25

(82.6mm

)

2.00

(50.8mm)

7.63 Dia

(195.1mm)

2.00

(50.8mm)

6.50 Dia

(165.1mm)

(50.8mm)

NPT. DISCH.

Содержание PROSSER PUPP512 Series

















Результаты поиска

Содержание PROSSER PUPP512 Series

Отзывы:

Похожие инструкции для PROSSER PUPP512 Series

Бренды по названию

Популярные бренды

Crane PROSSER PUPP512 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание PROSSER PUPP512 Series

Отзывы:

Похожие инструкции для PROSSER PUPP512 Series

Бренды по названию

Популярные бренды