Craftsman CMCVS001BOGOHP, Инструкция по эксплуатации

Страница: 10 / 36

English
8
Use
This vacuum cleaner can be used in one of four ways.
• With the extension tube
6
and the floor brush
10
.
(Fig. G)
• With the floor brush
10
. (Fig. H)
Installing and Removing the Battery Pack
(Fig. F)
nOTE:
For best results, make sure your battery pack is
fully charged.
To install the battery pack
14
into the tool handle, align the
battery pack with the rails inside the tool’s handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
15
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
OPERATION
WARNING:
To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Assembly (Fig. D)
1. Align the top of the extension tube
6
with the vacuum
inlet
5
as shown in Fig. D.
2. Push the extension tube
6
onto the vacuum inlet
5
so it
locks into position.
3. Align the bottom of the extension tube
6
with the floor
brush 10 as shown in Fig. D.
4. Push the bottom of the extension tube
6
onto the floor
brush 10 so it locks into position.
5. To remove an accessory, press the accessory release
latch 7 located on the vacuum inlet or the bottom
of the extension tube and gently pull the connected
accessory off.
WARNING:
When not in use position the
unit with the rear of the vacuum facing a wall so that
any inadvertent fall of the unit would contact a wall
and not people or pets.
ASSEMBLY AND ADJUSTMENTS
WARNING:
To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
VersaTrack™
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN VersaTrack™ Trackwall. Hooks and accessories
are sold separately. Please refer to the VersaTrack™ Trackwall
accessory sheet for further information.
A cold battery pack may charge at a slower rate than a warm
battery pack.
The hot/cold pack delay will be indicated by the green light
continuing to blink but with the red light continuously
ON. Once the battery pack has reached an appropriate
temperature, the red light will turn OFF and the charger will
resume the charging procedure.
Electronic Protection System
Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge. The tool will automatically
turn off and the battery pack will need to be recharged.
Important Charging Notes
1. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
2. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.