9
English
WARNING:
Always use proper eye
protection that conforms to ANSI Z87.1 (CAN/CSA
Z94.3) while operating this appliance.
CAUTION:
Before you begin trimming, only
use the appropriate type of cutting line.
CAUTION:
Inspect area to be trimmed and
remove any wire, cord, or string‑like objects which
could become entangled in the rotating line or spool.
Be particularly careful to avoid any wire which might
be bent outwardly into the path of the appliance, such
as barbs at the base of a chain link fence.
OPERATION
WARNING:
To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Releasing the Cutting Line (Fig. A)
In transit, the cutting line is taped to the spool housing
12
.
• Remove the tape holding the cutting line to the
spool housing.
Installing the Guard (Fig. E)
WARNING:
Never remove the guard.
Damage or personal injury could result.
WARNING:
NEVER OPERATE
APPLIANCE WITHOUT GUARD FIRMLY IN PLACE.
The guard must always be properly attached on the
appliance to protect the user.
1. Remove the guard screw
15
.
2. Slide the guard
11
fully onto the trimmer head
16
.
Make sure the tabs
17
on the guard engage the ribs on
the trimmer head.
3. Continue to slide the guard on until it “snaps”into place.
The locking tab should snap into the housing slot.
4. Using a crosshead screwdriver, insert the guard screw
and tighten securely.
5. Once the guard is installed, remove the covering from the
line cut-off blade, located on the edge of the guard.
WARNING:
Always check to make sure
that the detent lock is completely secured in place.
If the detent lock is not completely secured it could
result in the assemblys becoming disconnected
creating a hazardous condition. Periodically check the
connections to insure that the detent lock is completely
secured in place.
Assembling Upper and Lower Poles (Fig. D)
To Attach the Poles:
1. When installing the lower pole
5
into the upper pole
4
,
align the detent lock
6
with the detent slot
7
as shown
in Fig. D.
2. Press the two poles together so the detent lock
6
engages the detent slot
7
.
ASSEMBLY AND ADJUSTMENTS
WARNING:
To reduce the risk of serious
personal injury, turn unit off and remove the
battery pack before making any adjustments or
removing/installing attachments or accessories,
when replacing line, or prior to cleaning.
An
accidental start‑up can cause injury.
Wall Mounting
Some CRAFTSMAN chargers are designed to be wall
mountable or to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an electrical
outlet, and away from a corner or other obstructions which
may impede air flow. Use the back of the charger as a
template for the location of the mounting screws on the wall.
Mount the charger securely using drywall screws (purchased
separately) at least 1” (25.4 mm) long, with a screw head
diameter of 0.28–0.35” (7–9 mm), screwed into wood to an
optimal depth leaving approximately 7/32” (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in the slots.
VersaTrack™
WARNING:
Do not charge batteries while
charger is hung on Trackwall.
CRAFTSMAN chargers can be stored on CRAFTSMAN
VersaTrack™ Trackwall. Hooks and accessories are sold
separately. Please refer to the VersaTrack™ Trackwall accessory
sheet for further information.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
3. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING:
Shock hazard. Disconnect the
charger from the AC outlet before cleaning. Dirt and
grease may be removed from the exterior of the charger
using a cloth or soft non‑metallic brush. Do not use
water or any cleaning solutions.
