manualshive.com logo in svg

Craftsman 944.364230, Руководство пользователя, Страница: 10 / 12

Поделиться
Скачать
Craftsman 944.364230 Скачать руководство пользователя страница 10

10

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

SAE VISCOSITY GRADES

-20

0

30

40

80

100

-30

-20

0

20

30

40

F
C

32

-10

10

60

5W-30

SAE 30

LAWN MOWER

Always observe safety rules when per-
 form ing any main te nance.

TIRES

•   Keep tires free of gasoline, oil, or insect 

control chemi cals which can harm rub-
ber.

•   Avoid stumps, stones, deep ruts, sharp 

objects and other hazards that may 
cause tire damage.

BLADE CARE

For best results, blade must be kept sharp.  
Re place bent or dam aged blades.

TO REMOVE BLADE
1.   Disconnect spark plug wire from spark 

plug and place wire where it cannot 
come in contact with plug.

2.   Turn lawn mower on its side. Make 

sure air fi lter and carburetor are up.

3.   Use a wood block between blade and 

mower hous ing to prevent blade from 
turning when re mov ing blade bolt.

NOTE:

  Protect your hands with gloves 

and/or wrap blade with heavy cloth.
4.   Remove blade bolt by turning counter-

clockwise. 

5.   Remove blade and attaching hard-

 ware (bolt, lock wash er and hardened 
wash er).

NOTE

:  Remove the blade adapter and 

check the key inside hub of blade adapter. 
The key must be in good con di tion to work 
properly. Replace adapter if damaged.

TO REPLACE BLADE 
1.   Position the blade adapter on the en-

gine crank shaft. Be sure key in adapter 
and crankshaft keyway are aligned.

2.   Position blade on the blade adapter 

aligning the two (2) holes in the blade 
with the raised lugs on the adapter.

3.   Be sure the trailing edge of blade (op-

posite sharp edge) is up toward the 
engine.

4.   Install the blade bolt with the lock 

washer and hardened washer into 
blade adapter and crankshaft.

5.   Use block of wood between blade and 

lawn mower housing and tighten the 
blade bolt, turning clockwise.

•   The recommended tightening torque is 

35-40 ft. lbs.  

IMPORTANT

:  Blade bolt is heat treated.  

If bolt needs replacing, replace only with 
approved bolt shown in the Repair Parts 
section of this manual.

TO SHARPEN BLADE

NOTE

:  We do not recommend sharp en ing 

blade - but if you do, be sure the blade is 
balanced. 
Care should be taken to keep the blade 
balanced. An un bal anced blade will 
cause eventual damage to lawn mower or 
engine. 
•   The blade can be sharp ened with a fi le 

or on a grinding wheel. Do not attempt 
to sharpen while on the mower.

•   To check blade balance, drive a nail into 

a beam or wall. Leave about one inch of 
the straight nail ex posed. Place center 
hole of blade over the head of the nail. 
If blade is balanced, it should remain in 
a horizontal position. If either end of the 
blade moves downward, sharpen the 
heavy end until the blade is balanced.

GRASS CATCHER

(If purchased as an accesssory)
•  The grass catch er may be hosed with 

water, but must be dry when used.

•   Check your grass catcher often for dam-

age or de te ri o ra tion.  Through normal 
use it will wear.  If catcher needs replac-
ing, replace only with ap proved replace-
ment catcher shown in the Repair Parts 
section of this manual.  Give the lawn 
mower model number when ordering.

Blade adapter

Blade 
bolt

Crankshaft 

keyway

Hardened 
washer

Lockwasher

Blade adapter

Key

Blade

Trailing edge

Crank 

shaft

ENGINE

LUBRICATION

Use only high quality detergent oil rated with 
API service classifi cation SF-SJ.  Select the 
oil's SAE viscosity grade according to your 
expected operating temperature.

15

Loss of power        

1.   Rear of mower housing or       1.   Raise cutting height.    

                                      blade dragging in grass.               
                                2.   Cutting too much grass.           2.   Raise cutting height.
                                3.   Dirty air fi lter.                           3.   Clean/replace air fi lter.
                                4.   Buildup of grass, leaves,          4.   Clean underside of mower 
                                      and trash under mower.                 housing. 

 

                                5.   Too much oil in engine.            5.   Check oil level.
                                6.   Walking speed too fast.           6.   Cut at slower walking speed.

Poor cut –               

1.   Worn, bent or loose blade.      1.   Replace blade. Tighten  

uneven                    

                                                           blade bolt.

                                2.   Wheel heights uneven.            2.   Set all wheels at same  
                                                                                            height.

 

                               3.   Buildup of grass, leaves           3.   Clean underside of  

 

                                      and trash under mower.                 mower housing.

Excessive

              1.   Worn, bent or loose blade.      1.   Replace blade. Tighten  

vibration                 

                                                           blade bolt.

                                2.   Bent engine crankshaft.           2.   Contact a Sears or other
                                                                                            qualifi ed service center.

Starter rope

           1.   Engine fl ywheel brake is on     1.   Depress control bar to 

hard to pull                  

when control bar is released.         upper handle before    

                                                                                            pulling the starter rope.
                                2.   Bent engine crankshaft.           2.   Contact a Sears or other
                                                                                            qualifi ed service center.
                                3.   Blade adapter broken.             3.   Replace blade adapter.
                                4.   Blade dragging in grass.          4.   Move lawn mower to cut  
                                                                                            grass or to hard surface.

Grass catcher

        1.  Cutting height too low.             1.   Raise cutting height.

not fi lling

               2.   Lift on blade worn off.              2.   Replace blade. 

(If so equipped)

     3.   Catcher not venting air.            3.   Clean grass catcher.

Hard to push

         1.   Grass is too high or wheel       1.   Raise cutting height.

                                      height is too low.
                                2.   Rear of mower housing or       2.   Raise rear of mower housing
                                      blade dragging in grass.                one (1) setting higher.
                                3.   Grass catcher too full.              3.   Empty grass catcher.
                                4.   Handle height position not       4.   Adjust handle height to suit.
                                      right for you.

PROBLEM                 CAUSE                                        CORRECTION 

TROUBLESHOOTING - See appropriate section in manual unless directed 
to a Sears Service Center.

Содержание 944.364230













Отзывы:

Нет отзывов