background image

A01908

3- ENG

RISK OF 

EXPLOSION -

INCOMPATIBLE

MATERIALS

The solvents 1,1,1-Trichloroethane and
Methylene Chloride can chemically
react  with the aluminum used in most
spray equipment, and this gun and
cup, to produce an explosion hazard
and could result in serious injury or
death.

Read the label or data sheet for the
material you intend to spray.
1. Never use any type of spray

coating material containing these
solvents.

2. Never use these solvents for

equipment cleaning or flushing.

3. If in doubt as to whether a

material is compatible, contact
your material supplier.

Some paints, coatings and solvents
may cause lung damage, and burns if
inhaled or allowed to come into con-
tact with skin or eyes.

Use a 

NIOSH

approved mask or

respirator and protective clothing
designed for use with your specific
application and spray materials.
Some masks provide only limited
protection against toxic materials
and harmful paint solvent. Consult
with a Safety Expert or Industrial
Hygienist if uncertain about your
equipment or materials.

RISK TO 

BREATHING

RISK FROM 

FLYING OBJECTS

Certain parts are under pressure
whenever the gun is connected to a
pressurized air line. These parts may
be propelled if the gun is disassem-
bled.

Compressed air may propel dirt, metal
shavings, etc. and possibly cause an
injury.

Prolonged exposure to air spray can
result in permanent damage to hearing.

Disconnect the gun from the air
line, or completely depressurize the
air line whenever the gun is to be
disassembled.

Never point any nozzle or sprayer
toward a person or part of the
body.

Always wear ANSI 278.1 safety
approved goggles or glasses when
spraying.

Always wear hearing protection
when operating spray equipment.

•  SAVE THESE INSTRUCTIONS •

IMPROPER OPERATION OR MAINTENANCE OF THIS PRODUCT
COULD RESULT IN SERIOUS INJURY AND PROPERTY DAMAGE.
READ AND UNDERSTAND ALL WARNINGS AND OPERATING
INSTRUCTIONS BEFORE USING THIS EQUIPMENT.

The Following Hazards Can Occur During The Normal Use Of This Product:

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

When paints or materials are
sprayed, they are broken into very
small particles and mixed with air.
This will cause certain paints and
materials to become extremely
flammable and could result in serious
injury or death.

Never spray near open flames or pi-
lot lights in stoves or heaters.

Never smoke while spraying.

Provide ample ventilation when
spraying indoors.

RISK OF 

EXPLOSION OR

FIRE - 

FLAMMABLE 

MATERIALS

IMPORTANT SAFETY INSTRUCTIONS

Содержание 919.716051



















Отзывы: