Craftsman 315.214770 Скачать руководство пользователя страница 23

Страница: 23 / 32

TROUBLESHOOTING

PROBLEM

CAUSE

SOLUTION

Motor will not run.

1. Problem with On-Off switch or
power cord.

2. Motor defective.

1. Have worn parts replaced before
using band saw again.

2. Do not attempt any repair. Have
tool repaired by a qualified service
technician.

Blade does not run in the approximate
center of the upper wheel.

1. Not tracking properly.

1. Adjust tracking. See

Adjustments

section,

Tracking the Blade

Band saw slows down when cutting.

1. Cutting too small a radius.

2. Dull blade.

1. Stop feeding and back up the
material slightly until the band saw
speeds up.

2. Replace blade.

Blade breaking.

1. Too much blade tension.

2. Kink in blade caused by cutting too
small radius or turning the material
too fast when cutting.

3. Thrust bearings scarred or not
rotating.

1. Adjust tension. See

Adjustments

section,

Adjusting Blade Tension

2. Use correct cutting technique. See
section,

Operation.

3. Replace the thrust bearings. See

Adjusting Thrust Bearings

Saw is noisy when running.

1. Too much blade tension.

2. Blade guides and bearings are in
contact with the blade.

1. Adjust tension. See

Adjustments

section,

Adjusting Blade Tension

2. Adjust upper and lower blade
guides and bearings. See

Adjustments

sections,

Adjusting Thrust Bearings,

Blade Guide Support, and Blade
Guides.

Blade will not cut straight.

1. Blade guides and bearings not
properly adjusted.

2. Worn or defective blade.

1. Adjust upper and lower blade
guides and bearings. See

Adjustments

sections,

Adjusting Thrust Bearings,

Blade Guide Support, and Blade
Guides.

2. Replace blade.

Blade guides will not stay in position.

1. Blade guide screws have loosened. 1. Tighten blade guide screws

securely.

Содержание 315.214770

































Результаты поиска

Содержание 315.214770

Отзывы:

Похожие инструкции для 315.214770

Бренды по названию

Популярные бренды

Craftsman 315.214770, Руководство оператора

Результаты поиска

Содержание 315.214770

Отзывы:

Похожие инструкции для 315.214770

Бренды по названию

Популярные бренды