Craftsman 315.212400 Скачать руководство пользователя страница 16

Страница: 16 / 24

31.6

22.5

31.6

22.5

31.6

22.5

31.6

SQUARING THE SAW BLADE TO THE
FENCE

See Figures 17 - 20.

■

Unplug your saw.

WARNING

: Failure to unplug your saw could

result in accidental starting causing possible
serious personal injury.

■

Pull the saw arm all the way down and engage
the lock pin to hold the saw arm in transport
position.

■

Loosen the miter lock handle approximately
one-half turn.

■

Depress the miter lock plate and rotate the miter
table until the pointer on the control arm is
positioned in the postive stop at 0

■

Release the miter lock plate and securely tighten
the miter lock handle.

■

Lay a framing square flat on the miter table. Place
one leg of the square against the fence. Slide the
other leg of the square against the flat part of saw
blade.

Note: Make sure that the square contacts the flat
part of the saw blade, not the blade teeth.

■

The edge of the square and the saw blade should
be parallel as shown in figure 17.

■

If the front or back edge of the saw blade angles
away from the square as shown in figures 18 and
19, adjustments are needed.

■

Using the 8 mm hex key provided, loosen the
socket head screws that secure the mounting
bracket to the miter table.

See Figure 20.

■

Rotate the mounting bracket left or right until the
saw blade is parallel with the square.

■

Retighten the screws securely and recheck the
blade-to-fence alignment.

ADJUSTMENTS

Fig. 17

MITER TABLE

VIEW OF BLADE

SQUARE WITH FENCE

BLADE

FENCE

FRAMING

SQUARE

MITER

LOCK

PLATE

MITER

LOCK HANDLE

Fig. 19

Fig. 18

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

VIEW OF BLADE NOT SQUARE WITH

FENCE, ADJUSTMENTS ARE REQUIRED

FRAMING SQUARE

FENCE

MITER

TABLE

BLADE

FRAMING SQUARE

FENCE

MITER TABLE

BLADE

After squaring adjustments have been made, it may
be necessary to loosen the scale indicator screw and
reset the indicator to zero.

Fig. 20

MOUNTING BRACKET

8 mm SOCKET

HEAD SCREWS

8 mm HEX KEY

MITER TABLE

Содержание 315.212400

























Результаты поиска

Содержание 315.212400

Отзывы:

Похожие инструкции для 315.212400

Бренды по названию

Популярные бренды

Craftsman 315.212400, Руководство пользователя

Результаты поиска

Содержание 315.212400

Отзывы:

Похожие инструкции для 315.212400

Бренды по названию

Популярные бренды