background image

5

WARNING!

 READ AND UNDERSTAND ALL 

INSTRUCTIONS.

 Failure to follow all instructions 

listed below, may result in electric shock, fire  
and/or serious personal injury.

  

Before using battery charger,

 read all instructions 

and cautionary markings in this manual, on battery 
charger, battery, and product using battery to prevent 
misuse of the products and possible injury or damage.

CAUTION: 

To reduce the risk of electric shock 

or damage to the charger and battery, charge 
only nickel-cadmium rechargeable batteries as 
specifically designated on your charger. Other 
types of batteries may burst, causing personal 
injury or damage.

  

Do not use charger outdoors or expose to wet or 
damp conditions. 

Water entering charger will increase 

the risk of electric shock.

  

Use of an attachment not recommended or sold 
by the battery charger manufacturer may result in 
a risk of fire, electric shock, or injury to persons. 

Following this rule will reduce the risk of electric shock, 
fire, or serious personal injury.

 

  

Do not abuse cord or charger. 

Never use the cord to 

carry the charger. Do not pull the charger cord rather 
than the plug when disconnecting from receptacle. 
Damage to the cord or charger could occur and create 
an electric shock hazard. Replace damaged cords 
immediately.

  

Make sure cord is located so that it will not 
be stepped on, tripped over, come in contact 
with sharp edges or moving parts or otherwise 
subjected to damage or stress.

 This will reduce the 

risk of accidental falls, which could cause injury, and 
damage to the cord, which could result in electric 
shock.

  

Keep cord and charger from heat to prevent 
damage to housing or internal parts.

  

Do not let gasoline, oils, petroleum-based products, 
etc. come in contact with plastic parts. 

They contain 

chemicals that can damage, weaken, or destroy plastic.   

  

An extension cord should not be used unless 
absolutely necessary. 

Use of improper extension cord 

could result in a risk of fire and electric shock. If 
extension cord must be used, make sure:

  a.  That pins on plug of extension cord are the 

 

same number, size and shape as those of 

 

plug on charger.

  b.  That extension cord is properly wired and in 

 

good electrical condition; and

  c.  That wire size is large enough for AC ampere 

 

rating of charger as specified below:

 

   

Cord Length (Feet) 

25' 

50' 

100'

   

Cord Size (AWG) 

16 

16 

16

   

NOTE:

 AWG = American Wire Gauge

  

Do not operate charger with a damaged cord or 
plug, 

which could cause shorting and electric shock. If 

damaged, have the charger replaced by an authorized 
serviceman.

  

Do not operate charger if it has received a sharp 
blow, been dropped, or otherwise damaged in any 
way. 

Take it to an authorized serviceman for electrical 

check to determine if the charger is in good working 
order. 

  

Do not disassemble charger. 

Take it to an authorized 

serviceman when service or repair is required. Incorrect 
reassembly may result in a risk of electric shock or fire.

  

Unplug charger from outlet before attempting any 
maintenance or cleaning to reduce the risk of 
electric shock.

  

Disconnect charger from the power supply when 
not in use. 

This will reduce the risk of electric shock 

or damage to the charger if metal items should fall into 
the opening. It also will help prevent damage to the 
charger during a power surge.

 

Risk of electric shock. 

Do not touch uninsulated 

portion of output connector or uninsulated battery 
terminal.

  

Save these instructions. 

Refer to them frequently 

and use them to instruct others who may use this 
tool. If you loan someone this tool, loan them these 
instructions also to prevent misuse of the product and 
possible injury.

WARNING:

 

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities 

contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these 
chemicals are:

• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure 
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust 
masks that are specially designed to filter out microscopic particles. 

SAFETY RULES FOR CHARGER

Содержание 315.114281



















Отзывы: