Craftsman 113.29501, Сборка, инструкция по эксплуатации и список запасных частей

Страница: 16 / 32

IN-RIPPING
-
refers to a when the blade i s
- , -
between the motor and the fence and p arallel to ~ h e fence.
(See figure To place the saw in this position, unlock
the yoke, swivel latch pin and rotate the
clockwise (viewing it from until
swivel pin automatically indexes the
the Position the motor on the radial arm until
the pointer on the "In-Ri
p
" scale indicates the desired width
of the finished cut board. Tighten the carriage lock knob
securely. Turn the saw "On" and lower the radial arm until
the saw blade cuts into the table top a
p
proximately
inch. Turn the saw "Off". Now adjust the saw guard and
anti-kick pawl cssembly as described in the paragraph "Rip-
ping". The board to be ripped must be fed into the saw
blade from the right-hand side of the table, therefore, the
normal position for the operator
i s
also at the right side
of the table. left hand safely clear of the blade and
holding the board to be ripped down against the table
and against
face of the fence as a guide, use the right
hand to feed the board into the saw. The left hand should
remain stationary, serving as a guide only. As the right
hand
the left hand, a push stick with
the hand to complete the cut. Do not leave a long
board unsupported so that the spring of the board causes
it to shift on the table.
A
support (described in "Cross-
cutting") may be used to support the board behind the
blade; and i f the board is very long, use another support
in front of the saw. Ripped boards up to 16-inches wide
can be cut in the In-Rip position.
OUT-RIPPING -- refers to a position when the motor
i s
between the biode and the fence. Normally, this position
is only used
the width of the required ripped board
cannot be cut from the in-rip position. Ripped boards up to
17-1
/2-inches wide can be cut in the out-rip position when
fence
i s
the front table. If the fence
is
moved to
extreme position against the table clamps, ripped
boards up to wide can be cut. To place the
saw in the out-rip position, the yoke be rotated and
indexed counterclockwise the cross-cut position
and locked. The some procedure for pre-cutting the table
top (see "In-Ripping") ond the anti-kickback
pawl assembly should be followed. The same procedure
for sawing
i s used except that the operator stands at the
left-hand side of the table and a push stick is normally
not required.
Resowing
i s
cutting thick boards into thinner ones with
a ripping operation. (See figure 42.) boards, up to
4-inches width can be in one pass;
but larger boards require two passes, one pass along each
edge of the
When two cuts from opposite edges are
required, these should be made to overlap
1
/2-inch from
the opproximatc center of the board. If the first cut
i s
too
deep, the kerf may close and bind the saw on the second
cut, with
of kickback. Also, when the kerf closes,
the two sides c f the cut are no longer parallel to the sow
blade, and the saw will cut into them to spoil their appear-
ance. Keep the same face of
board against the fence
when making both cuts. When cutting boards thicker than
4 inches, a
should be used which extends
above the table top.
BEVEL A N D MITER CUTS
cuts may be made from either a cross-cutting or rip-
ping position b y tilting the blade to the desired angle.
Miter cuts can
only a cross-cutting position
when the blade and radial orrn are at angle other
Figure
41
Figure 42
I
Figure 43
I
than to fence.
A
bevel cut i s a cut which is
both beveled and This cut i s made the
and radial at the desired miter angle to fcnce;
then the i s tilted ta the desired bevel angle.
This cut
i s
also referred to as a conipound miter. (See fig-
ure
43.)