background image

page 7

7. Wiring.

CAUTION

Be sure outlet box is properly grounded and 

that a ground wire (

GREEN

 or Bare) is present.

Make sure all electrical connections comply with Local 
Codes or Ordinances and the National Electrical Code. If 
you are unfamiliar with electrical wiring or if the 
house/building wires are different colors than those 
referred to in the instructions below, please use a 
qualified electrician.

Note

Excess lead wire length from the fan can be cut to 

the desired length and then stripped.

When fan is secured in place on the hanging bracket, 
electrical wiring can be made as follows:
Connect 

BLACK

 and 

BLUE

 wires from fan to 

BLACK

 

wire from ceiling.  Connect 

WHITE

 wire from fan to 

WHITE

 wire from ceiling. Connect all 

GROUND 

(

GREEN

) wires together from fan to 

BARE

/

GREEN

 wire 

from ceiling. 

Use wire connectors provided when 

making connections.

If you intend to control the fan light with a separate 
light switch connect 

BLUE

 wire from fan  to the 

BLACK

 (or 

RED

)

 

supply from the independent switch.

* Wrap each wire connector separately with 
electrical tape as an extra safety measure.

8. Wiring - Wall Control

Remove existing wall switch. Wire the

 

wall 

control 

as shown in diagram at right. 

 

Connect 

BLACK/WHITE

 wire from wall control 

to 

BLACK 

(

AC IN L

)

 

wire in outlet box. Connect 

BLACK 

wire from

 

wall control to 

BLACK 

(

AC IN 

L

) wire from fan (inside the outlet box). Connect 

BLUE

 wire from wall control to 

BLUE

 wire from 

light in the outlet box. 

Connect 

GREEN/YELLOW

 

ground wire from wall control to ground wire in the 
outlet box. 

Use wire connectors provided when 

making connections.

*Wrap each wire connector separately with 
electrical tape as an extra safety measure. 
Gently push wires and taped wire connectors 
into outlet box.

Attach wall control to outlet box and secure 
with screws from original wall switch. Attach 
plate (included) to wall control using 2 screws 
provided with the wall control.

plate

wall control

plate

screw

outlet box

BLACK

(AC IN L 

from fan)

BLACK

BLUE

GREEN/

YELLOW

BLACK

(AC IN L)

BLACK/WHITE

green/

bare 

 ground

BLUE

white

black supply wire

white supply wire

ground 
(green or bare)

*

ground

 (green

or bare)

from fan

black

white

blue

black

from ceiling

Содержание TG52























Отзывы: