Craftex Ct169 Скачать руководство пользователя страница 8

 

8

UNPACKING 

 

The machine is properly packaged and 
shipped complete in a carton for safe 
transportation. When unpacking, carefully 
inspect the carton to ensure that nothing 
has been damaged during transit. Open the 
carton and check that the grinder and the 
parts are in good condition. 

 

While doing inventory, if you can not find 
any part, check if the part is already 
installed on the machine. Some of the parts 
come preassembled. 
 

MOUNTING 

 

The CT169 Grinder with Belt Sander 
weighs 38 lbs. When mounting it on a 
workbench, make sure the workbench is 
capable of holding the weight of the 
machine and the surface of the workbench 
is level. 
 
The CT169 is provided with 4 pre-drilled 
holes on its base to allow it to be mounted 
on a workbench. 
 
To mount the CT169 on a workbench: 
 
Remove the rubber feet from the four 
mounting holes on the base of the machine. 
 
Place the machine on the workbench and 
mark using a pencil on the bench surface 
through the 4 holes on the base. 
 
Remove the machine and drill the 4 holes 
on the marked points using a proper size 
drill bit. 
 
Position the machine on the table with the 
holes on the base aligned with the holes on 
the workbench. 
 

 

 

Use bolts (not provided) that exceed the 
thickness of the base plus the thickness of 
the bench top and secure the machine to 
the workbench. 

 

Figure-2 Mounting holes 

 

 

EYE SAFETY SHIELD 

 

The CT169 is provided with an eye safety 
shield which is positioned at 1/8” from the 
grinding wheel to protect the operator’s face 
from the sparks produced on the grinding 
wheel during grinding. 
 
To install the eye safety shield: 
 
Make sure the switch is in the OFF position 
and the cord is disconnected from the 
power source. 
 
Attach the support bracket to the grinder 
using screw and washer provided. See 
figure-3. 
 
Attach the eye safety shield to the support 
bracket as shown in figure-3 using two 
screws and two nuts provided. 
 
  

Содержание Ct169
















Отзывы: