Craftex Ct169 Скачать руководство пользователя страница 4

 

4

 

 

 

 

ALWAYS

 read and understand the 

user manual before operating the 
grinder. 

 

 

MAKE SURE 

you are wearing safety 

glasses while operating the grinder or 
sander. The small particles becoming 
airborne during operation can 
seriously damage your eyes. 

 

 

ALWAYS 

wear a dust mask or a 

respirator while grinding or sanding. 
The dust produced during operation 
can lead to serious respiratory 
problems if inhaled. 

 

 

MAKE SURE 

before making any 

adjustments, servicing or installing 
parts, the switch is in the “OFF” 
position, and the cord is un-plugged 
from the power source. 

 

 

MAKE SURE 

the RPM of the wheel 

you are installing on the grinder is 
equal or higher than the speed of the 
grinder. Operating wheels at a higher 
speed than rated for may cause the 
wheel to lay apart, fly or break and 
may cause accident. 

 

 

MAKE SURE 

to keep your hands at a 

safe distance from the wheel. 

 

NEVER LEAVE 

the machine 

unattended while it is running. 

 

 

MAKE SURE

 to do a “ring test” on the 

grinding wheels before installation. 
Wheels that do not pass the test are not 
safe to use. See “page-11 for details. 

 

 

ALWAYS

 stand to the side of the 

grinder when turning it ON and let the 
wheel reach full speed. Stand at least 
one minute to the side of the grinder 
after startup. A damaged wheel can 
break apart and fly shortly after starting 
the grinder. 

 

 

DO NOT

 grind on the side of the wheel, 

unless the wheel is rated for side 
grinding. 

 

 

DO NOT 

over-tighten the grinding 

wheel. Excessive tightening can cause 
the wheel to crack during operation. 

 

 

MAKE SURE 

you have read and 

understood all the safety instructions in 
the manual and you are familiar with 
your grinder, before operating it. If you 
fail to follow the instructions given in this 
user manual, serious injury could occur.

 

WARNING 

The safety instructions given above can not be complete because the environment in 
every shop is different. Always consider safety first as it applies to your individual 
working conditions

CT169 - 8” BENCH GRINDER w/BELT SANDER 

SPECIFIC SAFETY INSTRUCTIONS

 

Содержание Ct169
















Отзывы: