Craftex CT052 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

Craftex CT052 Скачать руководство пользователя страница 12

12

The fence controls the depth of the dovetail
pins by limiting the distance that the router
travels. The router stops when the router
base hits the fence. The fence must be
adjusted parallel to the edge of the vertical
piece just like the template.

To adjust the fence:

1.

Mount a 7/16" 0.0 guide bushing in your

router base. Measure the amount that the
template overlaps the vertical piece.
Multiply that number by two. For example, if
the template is offset from the edge of the
vertical piece by 1/8" and thickness of the
side piece is 1 /2", then the overlap is 3/8".
So, 3/8" x 2 is 3/4".

2.

Now, add 1/32" to the distance you

calculated in step 1.

Measure the distance from the edge of the
router base to the edge of the guide
bushing and add it to the distance you
calculated in step 2.

The distance calculated in step 3 is the
distance that the fence should be back from
the template. Loosen the two fence lock
knobs and slide the fence into position.
Ensure that the fence is parallel to the front
of the template and tighten the two lock
knobs.

NOTE: The procedure above is not affected
by changing the router bit vertical depth of
cut.

When you've finished with all the
calculations, make a test run using some
scrap wood to check your positioning. Fine
tune if necessary.

FENCE ADJUSTMENT

Hint: When you have come up with a reliable number (E) for your router, base, bushing,
and wood thickness combination, record it here and keep it for future reference. (E) will be
different for different thickness of wood.

«
...
10
11
12
13
14
...
»

Содержание CT052





















Отзывы:

Нет отзывов