background image

READ CAREFULLY BEFORE  INSTALLING UNIT

These installation instructions are a general guide, and do not supersede applicable local codes and ordinances.  Before planning or
making the installation, be sure it complies with all phases of the local heating codes.  Or, in the absence of local codes, with the latest
edition of the National Fuel Gas Code, ANSI.Z223.1.  In Canada, see the current installation code CAN1-B149.

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with
the latest edition of the National Electrical Code ANSI/NFPA No. 70.  In Canada, see the current Canadian Electrical Code
C5AC22.1.

The ANSI standards are available from the American Gas Association, 1515 Wilson Blvd., Arlington, Virginia 22209.

The NFPA standards are available from the National Fire Protection Association, Batterymarch Park, Quincy, MA. 02269.

Canadian standards are available from International Approval Services,178 Rexdale Blvd.,Etobicoke,Ontario, Canada

 M9W 1R3.

NOTE:  If optional rear register kit is to be used, see supplemental installation instructions (No. 84504) and section marked
“Special Instructions for Rear Register Kit Application” prior to installation of Rough-In.

INTRODUCTION

THIS IS A GAS-FIRED, GRAVITY VENTED WALL FURNACE THAT WILL OPERATE SAFELY AND PROVIDE AN
EFFICIENT SOURCE OF HEAT WHEN INSTALLED, OPERATED AND MAINTAINED AS RECOMMENDED IN THESE
INSTALLATION AND OPERATING INSTRUCTIONS.  READ THESE INSTRUCTIONS THOROUGHLY BEFORE
INSTALLING, SERVICING, OR USING THE APPLIANCE.  IF YOU DO NOT UNDERSTAND ANY PART OF THESE
INSTRUCTIONS, CONSULT LOCAL AUTHORITIES, OTHER QUALIFIED INSTALLERS, SERVICE AGENCIES, THE GAS
SUPPLIER OR THE MANUFACTURER.

SPECIFICATIONS

Your vented wall furnace comes packed in a single carton.  (For wall thermostat models that includes the thermostat, thermostat
wire, and insulated staples).  Before installing the wall furnace check the rating plate to verify that the Model Number is correct
and that the wall furnace is equipped for the type gas you intend to use.

Model

Type

Type

BTU/Hr.

Vent

Gas

Shpg.

REAR  REG. KIT

 FAN KIT

No.

Control

Gas

Input

 Size

Inlet

FINISHED DIMENSIONS

Wt.

Model

Weight

 Model

Wt.

SINGLE WALL FURNACE

W251F Snap Bulb

Nat.

25,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W255F Wall Stat

Nat.

25,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W252F Snap Bulb

L.P.

25,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W256F Wall Stat

L.P.

25,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W351F Snap Bulb

Nat.

35,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W355F Wall Stat

Nat.

35,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W352F Snap Bulb

L.P.

35,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

W356F Wall Stat

L.P.

35,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

90  Lbs.

40542

5 Lbs.    WFF81   10 lbs.

DUAL WALL FURNACE

W501F Snap Bulb

Nat.

50,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

134 Lbs. N/A

N/A

WFF81   10 lbs.

W505F Wall Stat

Nat.

50,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

134 Lbs. N/A

N/A

WFF81   10 lbs.

W502F Snap Bulb

L.P.

50,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

134 Lbs. N/A

N/A

WFF81   10 lbs.

W506F Wall Stat

L.P.

50,000

4 ”

1/2”

16-1/2”Wx68”Hx6-1/2”D

134 Lbs. N/A

N/A

WFF81   10 lbs.

One or two fan kits may be used on dual-wall furnace.

CONTENTS

Page 2

Introduction................................................

2

Rear Register Kit Instructions....................................

 9

Specifications..............................................

2

Lighting Instructions...................................................  10/11

Safety Rules.................................................

3

Pilot Adjustment...........................................................

12

Clearances....................................................

3

Burner Flame Adjustment............................................

12

Controls........................................................

3

Maintenance Instructions...........................................

12

Combustion & Ventilation Air...................

4

WFF81 Fan Instructions..............................................  13/14

Venting..........................................................

5,6

Trouble Shooting Chart................................................ 15/16

Rough-In Instructions................................

6

Parts Drawing................................................................

17

Installation....................................................

8

Parts List........................................................................

18

Wiring Instructions.....................................

9

Warranty........................................................................

20

Содержание W251F and





















Отзывы: