COX 16.5HP, Руководство владельца/оператора

Страница: 4 / 50

11 June 2015 Page 4 Rev6 05/04/13
Owners Manual for Lawn Boss Models A14011M A14111M
Roll Pin type steering wheel
PRE-DELIVERY INSTRUCTIONS
INTRODUCTION:
The purpose of this procedure is to ensure the dealer/
distributor has made the necessary installations, adjust-
ments and checks, before the machine is operational. This
procedure begins upon receiving the crated mower and is
finalised once the mower has been either sold or leaves the
dealer/distributors premises. This is the minimum amount of
work required, however it should not be limited to only the
areas detailed in this procedure.
RESPONSIBILITY:
It is the responsibility of the dealer/distributors to ensure
that before a machine is delivered to a customer, it is in
perfect operational condition.
PROCEDURE:
CHECK ACCESSORIES SUPPLIED IN SEAT PROTECTION BAG

Engine owners manual

Owner/Operator manual

Ignition keys (AM015)

Spark plug spanner (AM295)

Spark plug spanner (AM005G0 16HP Honda)

Spark plug Spanner 13HP Honda

Tommy bar (AM007)

Steering wheel (SW13)

Roll Pin (DP10)

Set Screws M8X20 X 2

Nuts M8 Nyloc x 2

Seat Springs x 2 (13060)

Washer W05M202 x 2

Warranty Card

Pre-delivery Instruction Sheet
Remove the four seat bolts, shakeproof washers and plain
washers to remove the plastic bag protection from around
seat. Install the four seat bolts, shakeproof washers and
plain washers, making sure that the seat is adjusted into the
desired position by using the seat transmission slots, tighten
bolts.
TYRE PRESSURE
Before operation ensure that all tyre pressures are equal.
The maximum pressure allowed is 140 kpa (20 P.S.I.).
ENGINE OIL
Before operation ensure that engine oil level is to the full
mark on the dipstick. (Check engine owners manual if oil
needs to be added).
FUEL TAP
Ensure the fuel tap at the bottom of the LH side of fuel tank
is turned to the on position before attempting to start en-
gine. (Use unleaded fuel only).
Turn off fuel tap after use.
ASSEMBLE STEERING WHEEL TO MOWER
Roll Pin Type—
To attach the steering wheel, align the hole
in the steering wheel boss to the hole in the steering shaft
and use a hammer and suitable punch to drive the DP10 roll
pin in, through the hole in the steering shaft cover into the
steering wheel and shaft. Ensure that the pin is situated
centrally in the steering wheel boss and that the steering is
free to turn.
Keyed Type— Remove tape attaching woodruff key to
steering shaft. Remove the screw & washers attached to
the steering shaft. Lubricate taper on steering shaft with
grease or anti-seize. Place steering wheel with keyway
aligned with woodruff key on shaft. Assemble the screw and
washers onto the shaft with 1/2”a/f socket, extension &
wrench & tighten to 23Nm.
Press the steering wheel center cover into place using hand
pressure only.
SEAT SPRINGS
Install and tighten the two seat springs, bolts and nuts to
the bracket welded to the rear of the chassis, which is situ-
ated under the seat/transmission cover.
SAFETY SWITCHES
Park brake switch - With cutter lever disengaged, attempt
to start the engine without setting the park brake. Engine
should not start.
Disengagement Switch - While sitting on machine with
park brake set and cutter engaged, attempt to start ma-
chine. Engine should not start.
Seat Switch - While sitting on machine start engine, en-
gage cutter and lift weight from seat. Engine should cut
out.
CUTTER BELT
Ensure that when the cutter belt is in the disengaged posi-
tion that the belt does not overlap when squeezed together,
if this occurs adjust the cutter engage lever until correct
disengagement is achieved.
Bonnet shown in closed
position underneath dash
panel extension before
attaching bonnet strap.
Roll Pin type steering wheel