Covidien Newport e360 Скачать руководство пользователя страница 39

Страница: 39 / 154

Overhaul Procedures

Service Manual

2-15

2.8.2

Air and Oxygen Inlet Regulator Rebuild

To remove and install the air and oxygen inlet regulator, follow the procedure in section

4.16.3

“

Regulators, Inlet Blocks, and Flow Sensor Block

.”

Figure 2-12.

Inlet Regulator Rebuild



Note:

Inlet regulators must be outside of the ventilator for disassembly and reassembly.

To install the air and oxygen inlet regulators rebuild kits, refer to

Figure 2-12.

and perform the

following steps:

Unscrew the brass cover from the regulator (no tool should be needed).

Remove the spring, diaphragm, diaphragm washer, seat with o-ring, small spring, and ball.

Using the parts from the regulator rebuild kit (RRK1800M), replace the used parts by reversing the
disassembly.

Cover

Diaphragm

Slip ring

O-ring

Spring

Содержание Newport e360



























































































































































Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды

Covidien Newport e360, Руководство по обслуживанию

Результаты поиска

Содержание Newport e360

Отзывы:

Похожие инструкции для Newport e360

Бренды по названию

Популярные бренды