manualshive.com logo in svg

Covidien Newport e360, Руководство по обслуживанию

Поделиться
Скачать
Covidien Newport e360 Скачать руководство пользователя страница 80

Component Removal and Replacement

4-20 

 Service Manual

4.16.3

Regulators, Inlet Blocks, and Flow Sensor Block

Figure 4-15.  

Pneumatics Panel Assembly

Note:

To replace the regulators, inlet blocks, or the flow sensor block, all screws securing the pneumatic assembly to 
the back plate must be removed.

To replace the regulators, inlet blocks, and the flow sensor block, refer to 

Figure 4-15.  

and perform 

the following steps:

1.

Remove the pneumatic panel assembly by performing the procedure in section 

4.16

, “

Pneumatics Panel 

Assembly and Components

.”

2.

Remove the four screws (two per inlet block) securing the air and oxygen inlet blocks to PNL2102M.

3.

Remove the eight screws (four per valve) securing the air and oxygen PSOL valves to PNL2102M.

1

Inlet regulator (REG1800P)

4

PSOL valves 

2

Inlet block (BLK2115M)

5

Back panel (PNL2102M)

3

Flow sensor block (BLK2101M)

Содержание Newport e360



























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды