Covalue DR6000 Скачать руководство пользователя страница 24

Страница: 24 / 26

dealer.

2) 2Tone encode

The encoding template is set in the 2 tone call list. The details must be set if encoding is ON. The

radio transmits the 2 tone signaling when the programmed call button is pressed. (The side button

could be programmed as Call1/2/3/4). This function is programmed by the dealer.

MDC Signaling

This function can be enabled or disabled by the dealers through programming software.

MDC has 4 systems, in which different main ID, group ID, etc., could be set by the dealer.

1) MDC decode

The option MDC system can be set through the RX signaling system in the personal template. If

the received MDC code is same as the one set in the system, it can decode successfully. After the

radio received the correct MDC signaling, according to the Receive squelch mode set by the user,

the squelch will be ON. Then, the radio can receive the call and the orange LED light flashes.

2) MDC encode

If the PTT ID of the chosen channel is set as MDC, the MDC code will be transmitted when

calling.

■

Troubleshooting

No.

Problems

Solutions

The radio cannot be

switched on or no

display after switched

on.

Battery pack may not be installed properly. Remove the battery pack

and install it again.

Battery power may be insufficient. Recharge or replace the battery

pack.

The battery power

consume quickly after

charging.

The battery life is finished; please replace it with a new battery pack.

Cannot talk to or hear

other members in your

group.

The frequency or CTCSS/DCS signaling are not identical and please

reprogram it.

Make sure the setting of the selective signaling 5-Tone in he RX

Squelch Mode is proper.

Beyond the radio efficient communication range.

Other voices from

non-group members

are heard on the

channel.

Change the CTCSS/DCS tone, and make sure change the tone on all

radios in your group.

Please set 5-Tone selective signaling on the channel.

Communication range

is too small.

Make sure the antenna is well connected.

Make sure the antenna is the originally supplied one.

Check if the battery power is in the normal state.

Ask your local dealer to adjust the squelch level.

Unable to transmit.

Make sure the PTT button has been pressed completely.

Battery power may be insufficient. Recharge or replace the battery

pack.

Содержание DR6000



























Результаты поиска

Содержание DR6000

Отзывы:

Похожие инструкции для DR6000

Бренды по названию

Популярные бренды

Covalue DR6000, Инструкция по эксплуатации

Результаты поиска

Содержание DR6000

Отзывы:

Похожие инструкции для DR6000

Бренды по названию

Популярные бренды